Z_ISE20C-TF2Z061EN
Page 3 of 3
8 Function Selection mode
In measurement mode, press the
button between 3 and 5 seconds,
to display [F 0]. Select to display the function to be changed [F
□□
].
Press and hold the
button for 2 seconds or longer in function
selection mode to return to measurement mode.
∗
: Some products do not have all the functions. If no function is available or
selected due to configuration of other functions, [- - -] is displayed on the sub
display (right).
8.1 Default Function settings
The default setting is as follows.
If no problem is caused by this setting, keep these settings.
•
[F 0] Display units, switch output specifications and diagnostic
information selection function.
Units specification
Pressure range
Default setting
"Nil" or M
ISE20C(H)
MPa
ZSE20C(F)
kPa
P
ISE20C(H)
psi
ZSE20C(F)
•
[F 1] Setting of OUT1
Item
Default setting
Output mode
Hysteresis mode
Reversed output
Normal output
Pressure setting
ISE20C
: 0.500 MPa
ZSE20C
: -50.5 kPa
ZSE20CF
: 50.0 kPa
ISE20CH
: 1.000 MPa
Hysteresis
ISE20C
: 0.050 MPa
ZSE20C
: 5.1 kPa
ZSE20CF
: 5.0 kPa
ISE20CH
: 0.100 MPa
Delay time
1.5 msec
Display colour
OUT1 ON: Green / OUT1 OFF: Red
•
[F 2] Setting of OUT2 is the same setting as [F 1] OUT1.
•
Other parameter settings
Item
Default setting
[F 3] Digital filter setting
0.00 s
[F 4] Auto-preset function
Not used
[F 6] Fine adjustment of display value
0%
[F10] Sub display setting
std (Standard)
[F11] Display resolution setting
1000-split
[F14] Zero cut-off setting
0.0
[F80] Power saving mode
OFF
[F81] Security code
OFF
[F90] Setting of all functions
OFF
[F96] Number of pressurizing errors
-
[F98] Output check
N/A (normal output)
[F99] Reset to default settings
OFF
9 Other Settings
•
Snap shot function
The current pressure value can be stored to the switch output ON/OFF
set point.
•
Peak/bottom value indication
The maximum (minimum) pressure when the power is supplied is
detected and updated.
•
Zero clear function
The displayed value can be adjusted to zero if the measured pressure
is within
±
7%F.S (
±
3.5%F.S. for compound pressure) of the zero point
•
Key-lock function
The key-lock function is used to prevent errors occurring due to
unintentional changes of the set values.
For further details refer to the operation manual on the SMC website
(URL:
https://www.smcworld.com
).
10 How to Order
Refer to the operation manual on the SMC website (URL:
https://www.smcworld.com
) for How to order information.
11 Outline Dimensions
Refer to the operation manual or catalogue on the SMC website (URL:
https://www.smcworld.com
) for Outline Dimensions.
12 Maintenance
12.1 General Maintenance
Caution
•
Not following proper maintenance procedures could cause the
product to malfunction and lead to equipment damage.
•
If handled improperly, compressed air can be dangerous.
•
Maintenance of pneumatic systems should be performed only by
qualified personnel.
•
Before performing maintenance, turn off the power supply and be
sure to cut off the supply pressure. Confirm that the air is released to
atmosphere.
•
After installation and maintenance, apply operating pressure and
power to the equipment and perform appropriate functional and
leakage tests to make sure the equipment is installed correctly.
•
If any electrical connections are disturbed during maintenance,
ensure they are reconnected correctly and safety checks are carried
out as required to ensure continued compliance with applicable
national regulations.
•
Do not make any modification to the product.
•
Do not disassemble the product, unless required by installation or
maintenance instructions.
13 Limitations of Use
13.1 Limited warranty and Disclaimer/Compliance Requirements
Refer to Handling Precautions for SMC Products.
Caution
•
SMC products are not intended for use as instruments for legal
metrology.
Measurement instruments that SMC manufactures or sells have not
been qualified by type approval tests relevant to the metrology
(measurement) laws of each country.
Therefore, SMC products cannot be used for business or certification
ordained by the metrology (measurement) laws of each country.
14 Product disposal
This product shall not be disposed of as municipal waste. Check your
local regulations and guidelines to dispose of this product correctly, in
order to reduce the impact on human health and the environment.
15 Contacts
Refer to
www.smcworld.com
or
www.smc.eu
for your local distributor /
importer.
URL:
https://www.smcworld.com
(Global)
https://www.smc.eu
(Europe)
SMC Corporation, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, Japan
Specifications are subject to change without prior notice from the manufacturer.
© 2021 SMC Corporation All Rights Reserved.
Template DKP50047-F-085M
