SMC Networks PF3A801H-L, Operation Manual

Page: 33 / 104

-32-
No.PF
※※
-OMY0005
■
Default setting
Function
Default Settings
Sub display
(Right)
Applicable
Page
Main display
(Right)
Main display
(Left)
Sub display
(Left)
[F 0]
FLoW [rEF ] Select display units [ Std] Standard condition
Page 33
FLoW
[Unit] Units selection function

1
[ L] L/min
tEMP [ C]
o
C
PrES [ MPA] MPa
-
[NorP] Select NPN/PNP [ PNP] PNP output
[oUt1] Select the output of OUT1 [FLoW] Flow rate
[oUt2] Select the output of OUT2 [FLoW] Flow rate
[CoL ] Select display colour
[1SoG] Green when ON
Red when OFF (OUT1)
[F 1]
oUt1 [SW1 ] Select the target for setting [FLoW] Flow rate
Page 37
FLoW [ModE] Select switch mode [ HYS] Hysteresis mode
FLoW [1ot ] Select switch operation [ 1_P] Normal output
FLoW [P_1 ] Input the set value
[ 500] 500 L/min (PF3A801H)
[1000] 1000 L/min (PF3A802H)
FLoW [H_1 ] Input of hysteresis
[ 50] 50 L/min (PF3A801H)
[ 100] 100 L/min (PF3A802H)
FLoW [dtH1] ON delay time setting [0.00] 0 s
FLoW [dtL1] OFF delay time setting [0.00] 0 s
[F 2]
oUt2 [SW2 ] Select the target for setting [FLoW] Flow rate
Page 44
FLoW [ModE] Select switch mode [ HYS] Hysteresis mode
FLoW [2ot ] Select switch operation [ 2_P] Normal output
FLoW [P_2 ] Input the set value
[ 500] 500 L/min (PF3A801H)
[1000] 1000 L/min (PF3A802H)
FLoW [H_2 ] Input of hysteresis
[ 50] 50 L/min (PF3A801H)
[ 100] 100 L/min (PF3A802H)
FLoW [dtH2] ON delay time setting [0.00] 0 second
FLoW [dtL2] OFF delay time setting [0.00] 0 second
[F 3]
FLoW
[FiL ] Select digital filter
[ 1.0] 1 second
Page 45
PrES [0.10] 0.1 second
[F 6] PrES [FSC ] Display value fine adjustment [ 0.0] 0% Page 46
[F13] - [rEv ] Select reverse display [ oFF] Reverse display OFF Page 47
[F14]
FLoW
[CUt ] Select Zero cut-off setting
[ 1.0] 1%F.S. cut
Page 48
PrES [ 0.0] 0%
[F16]
PrES
[MES ] Measurement display setting
[diSP] Display
Page 52 tEMP [diSP] Display
AC [diSP] Display
[F30] AC [SAvE] Accumulated value hold [ oFF] Not stored Page 53
[F80]
-
[diSP] Display OFF mode [ on] Display ON Page 54
[F81] [Pin ]Security code [ oFF] Not used Page 55
[F90] [ALL ] Setting of all functions [ oFF] Not used Page 57
[F96] [CYCL] Check of cycle time [- - -. -] No input signal Page 59
[F98] [tESt] Setting of output check [ n] Normal output Page 60
[F99] [ini ] Reset to the default settings [ oFF] Not used Page 68

1: Setting is only possible for models with the units selection function.