manualshive.com logo in svg

SMC Networks 7800A/VCP, Installation Manual, Page: 43 / 48

Share
Download
SMC Networks 7800A/VCP Installation Manual Download Page 43

G

LOSSARY

Glossary-3

Local Area Network 

(LAN)

 

A group of interconnected computer and support devices.

Media Access Control 

(MAC)

A portion of the networking protocol that governs access to the 
transmission medium, facilitating the exchange of data between network 
nodes.

Management Information Base

 (MIB)

An acronym for Management Information Base. It is a set of database 
objects that contains information about a specific device.

Plain Old Telephone Service 

(POTS)

One of the services using voice band. Sometimes used as a descriptor for 
all voice band services.

Private Branch Exchange 

(PBX)

A telephone exchange local to a particular organization who use, rather 
than provide, telephone services.

RJ-45 Connector

A connector for twisted-pair wiring.

Splitter

A filter to separate VDSL signals from POTS or ISDN signals to prevent 
mutual interference. (Note that an external splitter is not required for this 
CPE.)

TIA

Telecommunications Industry Association

Summary of Contents for 7800A/VCP

















































Reviews:

No comments