background image

www.smartpool.com

1. Provide an area that is free of any sharp objects with at least 6 hours of full sunlight a day.
2. Remove strap from collector and unroll it placing the headers with the serial

number label closest to your pool equipment.

3. Allow the collector to relax in the sun (30 minutes to an hour).  DO NOT LAY COLLECTOR ON

THE GRASS IT CAN DAMAGE THE LAWN UNDERNEATH! DO NOT WALK ON COLLECTOR.

4. Remove and discard the black protective end caps covering the threaded ends of the header pipes.
5. Wrap the threaded ends of the headers with Teflon tape provided (as shown) for a watertight seal.
6. On the header without the label, thread white end caps on the open ends (as shown). Be careful

not to cross-thread.

7. Thread connectors on the open ends of the header with the label (as shown).  Be careful

not to cross-thread. Use couplings and flex hose adaptors or soft-sided adaptor kit (SK28)

8. Turn off pool pump.
9. Go to pool and plug the round return fitting on the pool wall from the inside, so the water won't drain

through (a winter plug works well).

10.Connect a hose from the filter to the lower elbow connector. Always fill the system from the bottom.
11.Connect another hose from pool return fitting to other elbow connector.
12.From the inside of the pool wall, remove the plug you placed in the round return fitting. 

YOU ARE NOW READY TO START-UP YOUR SOLAR POOL HEATER

13. Turn on the pump. Check for leaks and tighten the connections that need attention.

Note:Upon start-up you will see air bubbles come through the return hose.  This is normal and will stop after all the air

has been purged from the solar heating system. 

SYSTEM LAYOUT

Single System

Required:

• Flathead screwdriver or 5/16" (8 mm) nut driver.
• To install your solar heating system you will require 2 hoses - one that will 

reach from the pool equipment to the collector and one that reaches from the

collector back to the pool.

Cool Water

(Feed)

Warm Water

(Return Fitting)

Pool Pump

Elbow Connector

Elbow Connector

White End Cap

5

6

7

White End Cap

Label

Filter

Feed Hose

Return Hose

Summary of Contents for SUNHEATER S210U









Reviews: