SmartKat Sailing boat Assembly Instructions Manual Download Page 19

 

WARRANTY CONDITIONS 

 
This is to certify that 

smartkat

 GmbH, Steyr, Austria, guarantees the product(s) indicated to be free 

from defects in material and workmanship under the conditions and with the limitations specified in 
this warranty. 
 
This warranty does not apply in countries where a national warranty applies, or in countries where 

smartkat

 is not represented. 

 
In countries where an applicable nonrestrictable law in any particular respect provides a better right 
to the customer than provided by this warranty, this warranty is void in that particular respect and the 
laws applies. All customers are recommended to make themselves acquainted with the basic content 
of such laws, if any. 
 

smartkat

 reserves the right to make changes in the products manufactured and/or sold by 

smartkat

 at any time without prior notice and without incurring any obligation to make the same or 

similar changes in products previously manufactured or sold. 
 
The warranty period starts on the date of delivery to the first owner/user. The date of delivery shall 
be noted on the warranty card, which is to be completed with all the relevant information and 
returned to the local 

smartkat

 importer. Remaining warranty is transferable to sub-sequent owners. 

 
All components or parts replaced or repaired under warranty will receive the remaining warranty of 
the original part or component. The warranty period is the minimum period which is indicated by 
applicable nondiscretionary legislation, if such exists. In the event that such legislation does not exist 
or prescribes a period shorter than the following, the warranty period will be as stated below. 
Constructive parts, equipment and accessories: 
 

24 months conditional on the use of the products for the private use and recreation of the 
owner, in this respect no commercial use, such as chartering or renting is permissible. 

 

To warrantee submitted hulls, sails, centreboard and rudder will be checked in any case 
for excessive, false and not the intended purpose appropriate demand before a warranty 
can be taken up by the buyer. 

 
The warranty covers the cost of replacing defective parts or of having such parts repaired or of 
obtaining equi-valent parts whichever is the lowest. A defective part or product in the sense of this 
warranty is a part or product that is found to have an inherent defect which exists in it at the time of 
delivery. (Transport costs for the replacement of defective parts overseas – outside continental 
Europe – are not part of this warranty). 
 
All warranty repairs must be carried out by an authorized 

smartkat

 importer or dealer during the 

normal working hours. This applies abroad as well. 
 
This warranty does not cover parts or products damaged during transportation, installation or repair or 
through abnormal use, overload, carelessness, insufficient maintenance, normal wear, use of spare 
parts other than 

smartkat

 parts, or through any type of incorrect installation, abuse, misuse, accident 

or through neglect or failure to follow instructions in the user manual, maintenance instructions, or 
installation instructions. The warranty is void if the user has taken abnormal risks or modifications have 
been performed which in the judgement of 

smartkat

 have caused or enhanced the damage or if the 

part or product has been used in violation of the law or for a clearly unintended purpose. 

 

Summary of Contents for Sailing boat
























Reviews: