Smartgen HGM9120 User Manual Download Page 7

Page: 7 / 58

HGM9120 Genset Controller

HGM9120 Genset Controller Version: 1.0 2014-04-14 Page 7 of 58

2 PERFORMANCE AND CHARACTERISTICS

♦

AMF (Automatic Mains Failure) function; also can be used as a single genset auto start

module by shielding mains signal or as an engine control module simply by shielding

generator signal in parameter setting interface.

♦

With ARM-based 32-bit SCM, highly integrated hardware, new reliability level.

♦

132x64 LCD with backlight; English interface.

♦

Improved LCD wear-resistance and scratch resistance due to hard screen acrylic;

♦

Silicon panel and pushbuttons for better operation in high/low temperature environment;

♦

Equipped with RS232/GSM communication port.

“Three remote” (remote control, remote

measuring and remote communication) function will be implemented if it is used as

monitoring port (use MODBUS RTU protocol), while SMS (Short Message Service)

function will be implemented if it is used as GSM port (GSM MODEM must be fitted,

SG361 module produced by Smartgen is recommended.) When genset is alarming,

controller can send short messages via SMS automatically to max. 5 telephone numbers.

besides, generator status can be controlled and checked using SMS.

♦

Suitable for 3-phase 4-wire, 3-phase 3-wire, single phase 2-wire, and 2-phase 3-wire

systems with voltage 120/240V and frequency 50/60Hz;

♦

Collects and shows 3-phase voltage, current, power parameter and frequency of

generator or mains.

Mains

Generator

Line voltage (Uab, Ubc, and Uca) Line voltage (Uab, Ubc, and Uca)

Phase voltage (Ua, Ub, and Uc) Phase voltage (Ua, Ub, and Uc)

Phase sequence Phase sequence

Frequency

Load

Current

IA, IB, IC, IE

Each phase and total active power

Each phase and total reactive power

Kvar

Each phase and total apparent power

kVA

Each phase and average power factor

Accumulate total generator power

kWh, kVarh, kVAh

♦

For Mains, controller has over and under voltage, over and under frequency, loss of

Summary of Contents for HGM9120



























































Search results

Summary of Contents for HGM9120

Reviews:

Related manuals for HGM9120

Brands by name

Popular brands

Smartgen HGM9120, User Manual

Search results

Summary of Contents for HGM9120

Reviews:

Related manuals for HGM9120

Brands by name

Popular brands