background image

Longo programmable controller LPC-2.CH1 special module

STANDARDS   AND   PROVISIONS:   Standards,   recommendations, 
regulations and  provisions of  the country in which the devices will 
operate, must be considered while planning and setting up electrical 
devices. Work on 230 VAC network is allowed for authorized personnel 
only.
DANGER   WARNINGS:   Devices   or   modules   must   be   protected   from 
moisture, dirt and damage during transport, storing and operation.
WARRANTY   CONDITIONS:   For   all   modules   LONGO   LPC-2   –   if   no 
modifications   are   performed   upon   and   are   correctly   connected   by 
authorized   personnel   –   in   consideration   of   maximum   allowed 
connecting power, we offer warranty for 24 months from date of sale 
to end buyer. In case of claims within warranty time, which are based 
on material malfunctions the producer offers free replacement. The 
method of return of malfunctioned module, together with description, 
can be arranged with our authorized representative. Warranty does 
not   include   damage   due   to   transport   or   because   of   unconsidered 
corresponding   regulations   of   the   country,   where   the   module   is 
installed.
This device must be connected properly by the provided connection 
scheme in this manual. Misconnections may result in device damage, 
fire or personal injury.
Hazardous  voltage   in  the  device  can  cause  electric  shock  and  may 
result in personal injury or death.
NEVER SERVICE THIS PRODUCT YOURSELF!
This device must not be installed in the systems critical for life (e.g. 
medical devices, aircrafts, etc.). 
If the device is used in a manner not specified by the manufacturer, 
the degree of protection provided by the equipment may be impaired.

Waste electrical and electronic equipment (WEEE) must be collected 
separately! 

LONGO LPC-2 complies to the following standards:

EMC:EN 61000-6-2 (EN 50082), EN 61000-6-4 (EN 50081)

LVD: IEC 61131-2

Vibrations and climatic-mechanical: EN 60068-2-6, EN 60068-2-27, 
EN 60068-2-29

Smarteh   d.o.o.   operates   a   policy   of   continuous   development. 
Therefore we reserve the right to make changes and improvements to 
any of the products described in this manual without any prior notice.

MANUFACTURER:
SMARTEH d.o.o.
Trg tigrovcev 1
5220 Tolmin
Slovenia

ii

Summary of Contents for LPC-2.CH1

















Reviews: