manualshive.com logo in svg

SmartBridges airBridge TOTAL, User Manual, Page: 10 / 21

Share
Download
SmartBridges airBridge TOTAL User Manual Download Page 10

1. Access Point - Normal 802.11b compliant Access 
Point. In this mode Client Info Tab will be enabled. 
2. Client Bridge - airPoint-PRO TOTAL acting as 
ethernet client, works in infrastructure mode. 
In this mode Site Survey Tab will be enabled. 
3. Wireless Bridge - airPoint-PRO TOTAL acting as 
wireless bridge connecting two or more ethernet 
LANs together. In this mode Wireless Bridge Tab 
will be enabled. 
Note: In Client Bridge mode airPoint-PRO TOTAL 
works with only those Access Points which support 
"Address 4" field in IEEE 802.11b specifications. 
To change the operating mode: 
1. Select Advanced Tab. 
2. Select the Operating mode. 
3. Click on Set Configuration. 
You will get a pop up window with the message 
"Operating mode changed successfully". 

 
Configuring airPoint-PRO TOTAL Operational Mode

 

 

 

 

● 

Client authorisation is a mechanism by which only 

authorised Wireless Clients are allowed to 
communicate with airPoint-PRO TOTAL. 

● 

By default the authorized client table is disabled and 

any Wireless Client can associate with airPoint-PRO 
TOTAL. 

● 

You can configure airPoint-PRO TOTAL to associate 

with the predetermined Wireless Clients by enabling 
the authorized Client table. To do this select Client 
Info Tab and check 'Use Authorisation Table' option. 

● 

Please key in the MAC addresses of the 

predetermined Clients in the window 

Summary of Contents for airBridge TOTAL






















Reviews:

No comments