background image

-8-

© September 2011 Smart Openers Pty Ltd

Setting Door Type

The Smart Lifter ECO has a specific program for one-piece 

(J-Type) tilt doors. In this mode the door moves slower to 

accommodate the shorter range of travel and wave action 

on a tilt door. Default = Sectional Mode

1

   Press and hold 

CODE

 + 

SET

 for 3 secs. The yellow 

open

 LED will light up indicating Sectional Mode. 

(Fig. 11).

2

   Press 

PB

 to change to Tilt Mode. The red 

close

 LED 

will illuminate.

3

   Press 

SET

 to save setting and exit.

Note:

 To revert to Sectional Mode repeat steps above.

Setting Limits Via Controller

1

   Press 

SET

 for 3 secs to enter set up mode.

2

   Press and hold 

PB

 to move the door to the desired 

open

 position and release (the yellow open LED will 

illuminate to indicate the open cycle). If you over shoot 

the desired position press 

CODE 

to drive the door 

down. Fig. 12.

3

   Press 

SET

 to confirm. 

4

   Press and hold 

CODE

 to move the door to the desired 

closed

 position (the red close LED will illuminate to 

indicate the close cycle). If you over shoot the desired 

position press 

PB 

to drive the door up. Fig. 13.

5

   Press 

SET

 to confirm. 

6

   The opener will now run through a full cycle to 

measure the force margin required to open and close. 

If no further settings or adjustments are required, the 

system is now ready to use.

Setting Limits Via Transmitter

You can set limits via a coded transmitter once the motor 

position has been set.

1

   Press 

SET

 for 3 secs to enter set up mode.

2

   Press 

TX Button 1

 to move the door to the desired open 

position. If you over shoot the desired position press 

Button 4 and move the door down.

3

  Pause for 5 secs to set. (Fig. 15).

4

   Press 

TX Button 4

 to drive the door to the closed 

position. If you over shoot the desired position press 

Button 1 and move the door up. 

5

   Pause for 5 secs to set. (Fig. 17).

If no further settings or adjustments are required, the 

system is now ready to use.

Resetting Limits

If you are not happy with the limits positions and you are 

still in the process of setting limits, pause for 10 secs to 

abort limits set up then press 

SET

 again for 3 secs and 

repeat initialising procedure as per above.

If limits set up and door force margin profile has been 

completed, to reposition limits press 

SET

 for 3 secs to 

reenter set up mode.

Fig. 14

Fig. 16

Fig. 15

Fig. 17

Press Button 1

to open door

Press Button 4

to close door

Pause for 5 secs

to set open limit

Pause for 5 secs 

to set close limit

Fig. 11 

Fig. 12 

Fig. 13   

Summary of Contents for ECO













Reviews: