Warnings and Safety Instructions
The main priority at Smart Flex is making sure that all
purchasers of our products enjoy them safely. We ask
that everyone reads this manual carefully and with caution.
Please observe all warnings and safety instructions.
FAILURE
to adhere to any of the warnings or cautions listed in this
manual could potentially void the warranty.
At the end
of this manual, there will be contact information. Please
email or call with questions or comments. Thank you for
purchasing your adjustable bed frame from Smart Flex.
Safety Precautions
Smart Flex strongly encourages that you read the instructions
completely before using this product. It is imperative
that you perform correct assembly and operation of your
adjustable bed to ensure ideal performance and longevity
from your SF-700/900 adjustable bed frame. We ensure
that this product has been thoroughly tested and
inspected for safety and functionality prior to sale.
Radio Frequency of the Device is 2.4 GHZ.
FCC compliance device complies with part 15 of the FCC
Rules under these two conditions:
1
.
This device does not cause any harmful interference.
2. This device will accept any interference received,
including interference causing undesired effect on the
operation.
Warnings
Medical Warnings
Pacemaker:
Consult your physician if you have a pacemaker
before using our SF-700/900 Adjustable Bed. The massage
feature of your SF-700/900 Adjustable Bed creates
vibration. It is possible for your pacemaker to interpret this
vibration as believing the user is moving and/or exercising.
Products that cause vibration have been known to have
this effect on pacemakers. Again, purchasers with
Pacemakers should consult their physicians before using a
SF-700/900 Adjustable Bed Frame.
Lifting of SF-700/900 Adjustable Bed
Consult a physician before lifting, moving or assembling your
SF-700/900 Adjustable Bed if you have ANY physical
restrictions concerning lifting. For example, customers
with Neck, Back, Shoulder, Arm, Hip, Knee, Foot and Ankle
conditions should consult their physicians before lifting
this product due to the product's weight and potential to
aggravate pre existing injuries or conditions.
In addition:
Any lifting of this product should be done by
a minimum of 2 persons. Product should always be in the
flat position before lifting.
Residential (In-Home) Use Only
Smart Flex makes no assertion that its products are designed
for any medical use. The product is not considered to be
a "hospital or medical" bed for commercial or residential
use. Smart Flex, Inc. has not designed this product to
meet hospital or medical standards as defined by the US
government.
In addition, do not attach Oxygen or additional medical
equipment to this product due to the risk of explosion.
Do not use any flammable gases, liquids or materials
near this product. This includes any medical equipment
that is potentially flammable.
Pinch Hazard
Never place Hands, Feet or any body part near the bed
frame itself while it is in motion to prevent all "pinching"
injuries. In addition, never place any body part under this
product while head and feet sections of the SF-700/900
Adjustable Bed are elevated. Any portion of the
SF-700/900 Adjustable Bed Frame that rests on the inner
frame has the potential to pinch or injure any body parts
placed under or between sections of the bed frame. Also
be cautious of areas where joints and hinges connect
the various parts of this product because those areas
could also cause pinching or injury if any body part is
placed there while Smart Flex Adjustable Bed Frame is in
motion.
Electrical Safety
IMPORTANT NOTE:
To ensure maximum safety, this product
should be plugged into an electrical surge protector and
not directly into the outlet. (Surge Protector is not supplied
with this adjustable bed)
Be sure to always unplug this adjustable bed frame from
the electrical outlet (surge protector) before performing
any cleaning or maintenance of the bed frame. Disconnect
any cord or cable safely by first removing the plug from
the outlet (surge protector). Keep its cords away from
heated and or moist surfaces. Stop using this adjustable
bed and contact the manufacturer for repair if: (1) its
cord or plug is damaged, (2) it is not functioning properly,
or (3) it has been damaged by dropping or any mishandling.
The use of adapters or any modifications is not recommended
unless the outlet is checked by a qualified electrician to
ensure proper grounding of the adapter or plug outlet.
NEVER REMOVE THE GROUNDING PIN OR ALTER THE PLUG
or input IN ANY WAY. Unauthorized modifications could
void the electrical component portion of your warranty.
For power safety, the massage motors will automatically
shut off when running continuously for 10 minutes. Please
press a massage button on the remote to re-engage the
massage feature.
MOTOR SHORT-CiRCUIT:
The input transformer voltage is
AC100-240V, 50/60Hz, 1.5A, the output voltage is DC 29V
2.0A, and the power rate is 50W. In case of a
short-circuit, a fuse on the transformer will burn out to
protect your motors. Please seek professional assistance
to replace the fuse.
Weight Ratings and Restrictions
Overload of Weight:
In the case of an overload of weight is
placed on the foot or head mechanism, the power supply of
the control unit will get overheated and shuts down functions.
Immediately remove the excess weight, and all functions will
resume after the temperature decreases. The recommended
weight limits on this adjustable bed is 750lbs.
Lifting and Lowering Cycles:
Do not sit on the head or the
foot of the bed while changing positions during the lifting or
lowering cycles, and when in the raised position.
Children and Pets:
It is imperative that no children or pets
play on or around The SF-700/900 Adjustable Bed to prevent
any injury. Do not allow small children to operate the
adjustable bed under any circumstances. Any individual with
diminished mental capacity should also not be allowed to
operate this product for safety reasons.
ADDITIONAL WARNINGS:
• If the SF-700/900 Adjustable Bed Frame needed to be
moved after assembly, be sure to move while product is in
the flat position with at least 2 people supporting the weight
of the product on both ends. Do not move this product in a
vertical or upright position to prevent injury on the
individuals or the product.
• Unplug this product from the electrical outlet (surge protector)
before attaching or removing any wires connected to the
control box or any other additional accessories.
• Do not insert any items into the control box input or USB
input that is not intended for use with this product or that
does not fit in any input.
• Do not use this product in the vicinity of aerosol spray
products or oxygen products /equipment.
• If there is any visible damage to the electrical cords or
control box, or any electrical component is discovered,
cease all operations of this product.
• Keep electrical power cord away from all heat sources.
Furthermore, if an electrical power cord is visibly damaged
or has been dropped in water or liquid, DO NOT USE.
• Do not expose any part of the SF-700/900 Adjustable Bed
Frame to moisture. A risk of fire or electric shock greatly
increases when any part of this product is exposed to
moisture.
Unpacking the Parts Included
1. Open the carton box and unfold the metal bed frame.
2. Then open all the boxes containing all the parts and only
cut zip ties for remote, power cord and mattress bar.
Do Not
cut the zip ties that tighten the USB Y cable, and underbed
LED light cable.
3. Please make sure you have all the parts of your adjustable bed
.
- 4 pcs corner legs
- 4 pcs Motor pins, 4 pcs Motor clips
- Foot mattress retainer (2 guards for king size bed)
- Multi Height 3 Sections Legs Extensions 3”+3”+3”
- Control Box
- Power Cord
- Power Supply Adapter
- Underbed LED Light
- Remote Control
- Foot Masage Motor covered by a pad (motor is not visible)
- Head Masage Motor covered by a pad (motor is not visible)
- Head Motor
- Foot Motor
- USB Y Cable
- Power Adapter Y Cable
- 2 Pairs of (4) USB Ports
- 2 AAA Batteries
- 2 9V Batteries(not included)
- Instruction Manual
Assembly of the Corner Legs to the Base
1. First, open up your SF-700/900 Box.
2. Unfold and lay down the bed base.
3. As you unfold the bed frame, the two center legs will
fold out. Please lay the frame flat with legs up
4. Then tighten the 4 corner legs
5. Use the adjustable leg heights that you prefer.
Motors Installation of the Control Box and
Massage Motors
1. Connect the Power Adapter to the control box with
one end of the Power Adapter Y Cable
2. Connect the power plug into the other side of the
power adapter box
3. With the USB Ports Y cable, connect the single
protruding pin to the remaining Power Adapter Y cable
and the other two ends of the cable to the USB Ports.
4. Connect the underbed LED lighting to the control box.
5. Connect the Head & Foot Massage Motors to the
control box
6. Connect the Head Motor to the control box.
7. Connect the Foot Motor to the control box.
8. Finally, your motors are installed to the control box.
10. Memory Position 1 (M1) is a function for you to program your
desired position. Press the Head/Foot Up and Down buttons to set
your desired position. Once you have set your desired position,
press and hold the M1 button until the remote backlight flashes
for approximately 2 seconds. Your M1 desired position is now set.
11. Press 11 once to preset TV position (Head Approx. 65
degrees, Foot Approx. 15 degrees)
12. Memory Position 2 (M2) to program a second desired
position. Follow the instructions for M1.
13. Press 13 once to turn on Head Massage at low intensity, press 13
the second time for medium intensity, third time for high intensity
and fourth time to turn off.
14. Button 14 has two functions: to turn the Head and Foot
Massage Off together or to set your massage timer.10 /20 /30
minutes Bar : When Button 14 ( Timer ) is pressed, this bar will
light up. Green light represents timer setting for massage
duration time. The default time is 10 minutes.
15. Press 15 once to turn on Foot Massage at low intensity, press 15
the second time for medium intensity, third time for high intensity
and fourth time to turn off.
16. Press 16 to turn On/Off the Underbed LED lighting.The
LED light will turn off automatically after 5 minutes of use.
17. Button 17 has two functions: to turn on the Head and Foot
Massage together or for setting different massage mode options.
18. Press 18 for Flashlight function at the top of the remote.
How to Sync Two Twin XL Bases into a King
1. Use only one remote provided. Pairing for the remote
A and Base A is already done by the manufacturer;
otherwise refer to Troubleshooting #8.
2. Connect the two control boxes with the Sync cable
as shown below.
3. Bases A and B should now be synced and paired with
the respective remote.
Troubleshooting
1. When there is no power, check to make sure all cords are
connected properly and the plug is inserted securely into the
power outlet. Test to ensure that the outlet has power.
2. When the LED power indicator light on the remote control
is off, replace 2 AAA batteries.
3. When the LED power indicator light on the transformer is
not on, replace the transformer.
4. When the LED power indicator lights are on but there is no
power, replace the motor.
5. When the massage does not work, ensure that all the cords
are inserted properly and if that still doesn’t work, replace the
massage unit by removing the massage sponge pad, replace
a new one, cover the sponge pad and insert the cord back
to the control box.Then, press the massage button to see if it
works now.
6. In case of no power supply, purchase two 9 volts batteries
and install them in the AC/DC power adapter as a battery
backup. This will allow the base to adjust back to the FLAT
position if the power goes out. Press the “FLAT” button to get
the bed flat after installing the two 9 volts batteries.
7. When there is power supply but the Head or Foot of the bed
is not functioning, replace the motor
8. If your remote control does not work then you must pair it
with the control box yourself. First, insert 2 AAA batteries
(included) into your wireless remote control. Pair your Wireless
Remote Control with the Control Box by pressing the Pairing
Button on the Control Box and holding then releasing (The
light will turn off then start flashing). Then, press the Head up
and Foot Up button on the remote at the same time. The
remote LED will start flashing. Release the head up and Foot
Up buttons and the LED will continue to flash and pair with the
control box. The LED will then turn off indicating pairing is
completed. Otherwise, repeat the above steps.
Warranty Information
Warranty Warning:
Any opening or tampering with the control
box, motors, remote or hand controls will void the warranty. Do
not alter component wiring or modify the structure of the product
in any way or the warranty will be voided. Only allow those
AUTHORIZED to conduct repairs and/or part replacements on
your adjustable bed to secure the product warranty.
Intended use
Smart Flex Adjustable Bed Frames are intended for In-Home
Residential use. Any changes, alterations, modifications or
unauthorized attachments to any part of this product will void
the warranty. Exceeding the recommended weight limits for
this product will also void the warranty.
Warranty Claims:
If a potential issue with your product arises and you wish to
make a claim, you must contact Smart Flex customer service
at 1-888- 444-9888 within 20 days of discovery of the issue.
Please keep the original sales receipt that was received from
the retailer at the date of purchase along with the model
number for any warranty claim.
1. Warranties are non- transferable and only given to the original
retail purchaser of the Smart Flex, Inc. Adjustable bed.
2. Your Smart Flex, Inc. Adjustable bed is warranted against any
defects of (1)All parts and full labor of the Smart Flex Adjustable
Bed for a period of 3 (Three) years including (ServeCo North
America, LLC. After Sales In-Home Service); (2) The metal frame
for a period of 20 years from the warranty commencement
date (purchasing date). Smart Flex, Inc. will send replacement
parts for any defective part to the purchaser at no cost upon
notice during the first year from the warranty commencement
date. If the purchaser does not return the defective part to
Smart Flex, Inc. within 20 days of receiving the replacement
part, the prescribed warranty shall not apply and purchaser
shall bear all service, labor, transportation and shipping costs
related to the delivery and replacement of the defective
part.
3. Warranty shall not apply if (1) the damage is caused by the
purchaser, (2) there has been any repair or replacement done
by an unauthorized person, (3) the adjustable base has been
mishandled through physical or electrical abuse or misuse, or
operated in an improper manner that is inconsistent with the
instructions outlined in the SF900, SF800, SF700, SF500, SF300,
SF200, or SF100 Instruction Manuals, (4) there is damage done
to the mattress, fabric, cables, or electricals, or (5) there is any
costs for unnecessary service calls.
Please note:
The decision to repair or replace components
shall be made by Smart Flex , Inc. The repair or replacement
of any part of this product should be for the sole purpose of
the purchaser. Smart Flex, Inc. shall bear no liability for any
special, indirect or incidental damages arising from a
warranty claim or repair; or on any damage, claim or loss not
covered by the terms of the Smart Flex, Inc. Adjustable Bed
warranty.
Contact Information:
Smart Flex, Inc.
623 Southwest Street,
High Point, NC 27260
1-888- 444-9888
Pairing the Remote Control to the Control Box
As the pairing procedure is already done by the manufacturer,
you can just insert 2 AAA batteries into your wireless remote
control and start to enjoy your SF-950 Adjustable Bed. If
your remote control fails to operate, please refer to
troubleshooting #8.
Wireless Remote Control Operation
1. Press and Hold on 1 to raise the head of the bed.
2. Press and Hold on 2 to raise both the head & foot of the bed
together.
3. Press and Hold on 3 to raise the foot of the bed.
4. Press and Hold on 4 to lower the head of the bed.
5. Press and Hold on 5 to lower both the head & foot of the bed
together.
6. Press and Hold on 6 to lower the foot of the bed.
7. Press 7 once to preset Zero G position (Head Approx. 20
degrees, Foot Approx.40 degrees)
8. Press 8 once to preset S/F position (Head Approx. 10 degrees,
Foot Approx. 0 degrees)
9. Press 9 once to preset Flat Position. (Head and Foot 0 degree)
13
Summary of Contents for SF-950
Page 1: ......
