SMART-AVI UXPRO, User Manual

Page: 2 / 2

Introduction
The
UXPRO
range of products allows the extension
of a wide range of video and audio formats, RS23 2/
IR
and USS via a single Category S Unshielded Twisted
Pair (UTP) cable.
Features
• Supports Dual Screens.
•
Uses easy to install, inexpensive CA T-S/Se/6/7 /8.
• Output reaches up to 27Sft (83.2 m).
• Resolutions up to l 900x l 200.
• 300 MHz Bandwidth.
• Sends high-resolution WUXGA, Stereo Audio signals,
RS232/IR from one source to 2 locations
•
Compatible with Line Level Stereo Audio Signals.
•
High ground loop immunity.
• Built-in lightning, power surge and transient
protection.
•
Designated trimmer in the remote unit to
compensate for cable length.
•
Compact Metal Ca.se Enclosure.
•
Supports
RS232/IR
and USS
•
Supports USS Keyboard, USS Mouse+ additional
USS
l.
l/
l.O
devices.
•
Compatable with VGA, XGA, SUN, MAC and SGI
•
Uses one CATS (UTP) cable for USS transmission.
• 4
port USS hub with RX (receiver) unit.
• External Power Supply.
• Uses on CATS
(UTP)
for each WUXGA/Audio/
RS232 and IR signal transmission.
What's in the box?
UXPRO
Please check the contents of the package before
beginning installation.
Oty Items Part No.
UXPro Transmitter Unit
UXP-TX
UXPro Receiver Unit
UXP-RX
s volt
de power
supply PS-SD IA-US
HDD
15
male
to
male VGA cable 16ftl
Audio
3.5
mm stereo miniplug cable
CC-ADMM06
IR EYE Receiver
SM-EYE
IR Emitter
SM-IED
Seria I m/f DB9
6ft. CCSERMF06
Installation Diagram
Connecting the Transmitter
l. Connect the output of the computer video card to the
video input of the transmitter using the included male
to male video cable.
2. Connect the output of the computer audio card to
the audio input of the transmitter using 3.Smm audio
male to male audio cable.
3. Connect local monitor to the VGA out of the
transmitter.
4. Connect external speakers to the transmitter's audio
out (Standard 3.Smm stereo miniplug)
S. In the back of the unit connect the CA TS cable that
will connect to the receiver (UXPRO RX)
6. Use AB Cable to connect the USS.
*NOTE: You can not use RS232 and IR at the same time.
Connecting The Receiver
l. Connect CATS cable (coming from the transmitter) to
the back of the receiver.
2. Connect
1-2
display monitors to the VGA out
connectors on the front of the receiver.
3. Connect
1-2
sets of external speakers to the audio
output connections on the front of the unit.
(Standard
3.Smm
stereo Miniplug)
4. Connect the USS devices.
*
NOTE: USS supported is l. l
Adjusting and Tuning the Signal
In order to fine tune the signal, adjust the individual
dials one at a time starting with GREEN, then BLUE,
and lastly
RED.
As
you turn the dials you will notice
the colors slightly change as you increase or decrease
the strength. All dials should be around the same
distance.
Model
UXP-RX
Preparing & Connecting System CATS Cable
Pair
I
Pins
I
& 2
Pair 2 P
i
ns 3 & 6
Pair 3 Pins 4 & 5
Pair
4 Pins 7 & 8
Connectors:
RJ-45
Capacitance: 14 pf/ft (46 2 pf,/m)
Conductor Gauge:
24
AWG