SMA Sunny Boy SWR 1800U Installation And Operator'S Manual Download Page 48

Page: 48 / 59

Sunny Boy 1800U

Installation and Operator’s Manual

SB2500U-11:NE

SMA Regelsysteme GmbH

7 Technical Data

Input (PV panel)

Maximum open circuit voltage of the PV panel

WARNING: It is essential to comply with the respective input voltage

range which varies depending on the type and number of PV mod-

ules used.

WARNING: The maximum open circuit voltage of the PV panel may

not exceed the specified maximum input voltage of the Sunny Boy.

The open circuit voltage of the PV panel depends on the temperature of its cells and

on the respective solar radiation. The highest open circuit voltage of the PV panel oc-

curs when the temperature of the cells is at its lowest point. Therefore it has to take

into account the lowest possible ambient temperature of the PV panel when planning

the PV plant. Based on this temperature and knowing the type of PV modules used

you can then determine the maximum open circuit voltage of the PV panel. You can

enter these data into our EXCEL

tool “GenAu“ and check whether the maximum ad-

missible input voltage of the Sunny Boy is not exceeded under any possible operating

conditions. You will find this tool in the Internet for download at:

http://www.sma.de/ftp/energietechnik/sunnyboy/GenAu/GenAu.exe

WARNING: The MPP-voltage of the connected PV-modules may not fall

below the specified range at 158°F (+70°C) (V

MPP +158

> min. input volt-

age range).

NOTE: The Sunny Boy can tolerate a current higher than the speci-

fied current as long as the voltage is within the specified range.

Summary of Contents for Sunny Boy SWR 1800U




























































Search results

Summary of Contents for Sunny Boy SWR 1800U

Reviews:

Related manuals for Sunny Boy SWR 1800U

Brands by name

Popular brands

SMA Sunny Boy SWR 1800U, Installation And Operator'S Manual

Search results

Summary of Contents for Sunny Boy SWR 1800U

Reviews:

Related manuals for Sunny Boy SWR 1800U

Brands by name

Popular brands