ENG
Instruction Manual SXL ECO
1. Use as directed:
This product serves exclusively lighting purposes and may:
only be used with a voltage of
230V ~50Hz
.
not be exposed to strong mechanical loads or to strong
contamination.
only be installed and operated after a condition inspection if the
product is dirty or has been moistened through storage.
not be modified or converted.
If these points named above are not adhered to, a short circuit or
electrical shock may occur!
2. Technical Data:
Operating voltage:
230V ~50Hz
Safety class:
I
Safety type:
IP 65
Bulb:
TC-DSE(TSE),
max.
25W
Dimensions (W/H/D):
31/42/12,5 cm
Swivel
range:
180°
Weight:
3,6
kg
Importeur:
SLV
Elektronik
GmbH
IP 65: Protection against dust(dust-tight) - Protection against jetted
water from all directions.
3. Installation
The electric connection may be executed only by an electric expert
who is familiar with the valid directives!
Attention:
Switch off the power of the mains supply line or
respectively of the connection lead before doing any works
.
Use only
parts, which are supplied with the product or are described as accessories!
Otherwise the product or the installation might not be sufficiently safe.
Installation place:
The product is suited for
wall and ceiling installation
.
Make sure that the product is mounted on a
stable, even and tilt-fixed
background
.
The
light exit
should be placed at least so far from the illuminated surface,
as indicated as
minimum distance
on the type plate of the luminaire:
0,5
m
.
Pay special caution
to easily inflammable objects.
Separate Installation Steps
You can establish the electrical connection before or after the
installation.
Installation
Prepare the drill holes according to the distance of the installation holes
on the mounting bracket. Do not damage the power supply line, i.e. by
drilling, screws or strong bending. This can lead to a short circuit.
Fasten the fixture to the installation surface using properly dimensioned
dowels and screws (1). Ensure a secure hold.
Electrical Connection
Loosen the four screws on the front of the housing cover (2) without
removing them completely. Fold back the upper screws and open the
housing cover (3).
Loosen the PG-screwing (4) and direct the power supply cable into the
housing. Refasten the PG-screwing.
The product must be able to be separated by an all pole separation from
the current supply.
For electric connection attach the black or brown wire (live conductor) of
the mains supply with the
clamp L
and the blue wire (neutral conductor)
of the mains supply with the
clamp N
. The green-yellow wire (protective
conductor) of the mains supply has to be tightly screwed into the
earth
clamp
of the product.
Inserting the bulb:
Use a piece of fabric when touching the bulb. Do not
touch the glass with bare fingers. Remove fingerprints from it. Ensure
secure fit of the bulb.
Close the housing cover. The gasket must fit properly. Fasten the
screws.
The product is now ready for operation.
4. Operation
:
Information for the user:
Operate the product only if it is working correctly. Switch off the product
with a malfunction immediately and operate it again only after examination
by an electrical specialist. This is the case, when:
visible damages appear.
the product does not work.
smoke, steam or crackling sounds appear.
an overheating is recognisable.
Repairs of the product or work on mains voltage-prominent sections may
only be carried out by qualified electricians.
Attention:
Here exists mortal danger from an electric shock!
How to avoid failure and fire risk:
Do not cover the product - provide free air circulation!
L
N
5
42 cm
31 cm
12,5 cm
1
2
4
3
2
Do not hang or fasten anything on the product, especially no
decoration.
Never let children play unsupervised with electric products! Children
can not always estimate dangers in dealing with electric energy correctly.
What is to do if a bulb is defect or does not work?
Disconnect the product from power
, before you exchange
the bulbs.
Caution:
Let the bulb
cool down
first before replacement –
otherwise considerable risk of injury exists because of the hot
surface.
Replace the bulbs only with bulbs of the same data like socket,
power and capacity. Every other sort of bulb can lead to
damages of the light.
Replacing the bulb
: see Installation.
5. What else has to be considered?
Disconnect the product from power
, before you…
clean or maintain the product.
do any works on the product or its components (electric expert).
F Mode d'emploi SXL ECO
1. A utiliser comme indiqué :
Ce produit ne sert qu’à éclairer:
il est prévu pour une tension de
230V ~50Hz.
il ne doit être soumis ni aux efforts mécaniques importants ni à un
encrassement important.
il ne doit être utilisé qu’après examen si le produit a été stocké dans un
entrepôt humide ou sale.
ne doit pas être modifié.
Un non-respect de ces points peut causer un court-circuit ou une
décharge électrique!
2. Informations techniques:
Tension d'alimentation:
230V ~50Hz
Classe de protection:
I
Degré de protection:
IP 65
Ampoule:
TC-DSE(TSE), max. 25W
Dimensions (L/H/P):
31/42/12,5 cm
Portée d’inclinaison:
180°
Poids: 3,6
kg
Importeur:
SLV
Elektronik
GmbH
229192 05/005
by SLV Elektronik GmbH
Technical Details are subject to change.
Duplication prohibited !
IP 65: Protection contre la pénétration de poussière - Protection contre jets
d’eau provenant de toutes les directions
