PAGE 3 OF 3
SloanLED Headquarters
5725 Olivas Park Drive, Ventura, CA, USA
888.747.4LED (888.747.4533) • [email protected]
SloanLED.com
SloanLED Europe b.v.
Argonstraat 110, 2718 SN Zoetermeer, NL
+31 88 12 44 900 • [email protected]
P/N 402591 Rev E 2022-10-11
Customer service and technical support
PosterBOX
ID
Installation Guide for 701946-6WLNP1, -6WSNP1
The SloanLED PosterBOX™ product family is licensed by Signify (formally Philips Lighting) in relation to the following patents: North America: US7841733. Europe: EP1938298,
NL1030161, NL2000273, DE202006020673.6. Asia: CN101300616. PosterBOX products are licensed under Signify’s EnabLED program when bought as a PosterBOX lighting
kit solution including a SloanLED power supply. Final application in which PosterBOX lighting kit solution is installed is covered by SloanLED's licensing agreement with Signify
and free from any further royalties relating to the patents listed above.
Troubleshooting
Entire sign or leg does not light
after complete installation.
Check connection from power supply lead to first module. Make sure polarity of connections made at power supply lead and any
jumper wire is correct. Power supply outputs should be connected RED-TO-RED STRIPED (+) and BLACK-TO-WHITE (-).
Still does not light.
Check output voltage of power supply using a voltmeter. Output voltage should be DC 24.0 V ± 0.5 V. If there is no output voltage,
have a licensed electrician check input voltage. Make sure power supply is connected correctly and getting primary power. If power
supply is connected properly and getting primary power and there is still no output voltage, try a different power supply.
Still does not light.
If power supply is getting primary power and modules don’t light, there may be a short in secondary wiring.
Check all connections and cap all loose wires.
The beginning of a leg lights,
but entire leg does not light or
lights intermittently.
The primary cause of a portion of a PosterBOX ID leg not lighting or lighting intermittently is a bad connection or reverse polarity
connection between modules that light and modules that don’t light. Check this connection.
One module does not light, but all
others in leg light.
PosterBOX ID is designed so if one module fails, it will not cause entire sign or leg to go out. If one module does not light, but all others
in leg do, replace this module with a new one.
If longer lead wire from power supply to LED product is needed, an extension can be used. Extension should be kept as short as possible,
i.e., under 15 ft use 18 AWG UL Listed PLTC (4.6 m for 1 mm² PLTC) or under 50 ft use 14 AWG UL Listed PLTC (15.2 m for 2.5 mm² PLTC).
Extension of Power Supply Leads
E215393
241542
24 VDC Power Supply Capacity Chart
Maximum units per power supply*
Power output
6WLNP1
6WSNP1
30 W
(EU/ROW ONLY)
1
3
60 W
3
7
96 W
6
12
3
×
96 W
3
×
6
3
×
12
100 W
6
12
150 W
(EU/ROW ONLY)
9
18
Power used per
unit in Watts:
14.0 W
7.2 W
Capacities based on 90% of power supply output.
NOTE:
Refer to "
SloanLED Power Supply Guide for Sign
Products
" for appropriate 24 V power supply models.
Scan QR code to
download
SloanLED
Power Supply Guide
for Sign Products
https://sloanled.com/PowerSupplyGuideForSignProducts
