background image

Code No. 0816490

Rev. 6 (05/16)

INSTALLATION INSTRUCTIONS FOR ELECTRONIC 

SENSOR-ACTIVATED LAVATORY FAUCETS

LIMITED WARRANTY

Unless otherwise noted, Sloan Valve Company warrants this product, manufactured and sold for commercial or industrial uses, to be free from defects in material and workmanship for a period of three (3) years 
(one (1) year for special finishes, SF faucets, PWT electronics and 30 days for PWT software) from date of first purchase. During this period, Sloan Valve Company will, at its option, repair, replace, or refund the 
purchase price of any product which fails to conform with this warranty under normal use and service. This shall be the sole and exclusive remedy under this warranty. Products must be returned to Sloan Valve 
Company, at customer’s cost. No claims will be allowed for labor, transportation or other costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company’s products directly from 
Sloan Valve Company for purpose of resale. This warranty does not cover the life of the batteries.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.

FAUCET ROUGH-IN

-ISM

  Integral Spout Mixer (All Series)

-IC

 

-Click Feature (All Series)

5-11/32”

(136 mm)

2-1/16” 

(52 mm)

2-9/16”

(65 mm)

24º

2-1/16”

(52 mm)

4-11/32”

(110 mm)

MODELS EAF-200/250/275 

0.5 gpm (1.9 Lpm) Max. Flow 

Faucets with Single Line Water Supply

MODELS EAF-200/225

*

/250/275 

0.5 gpm (1.9 Lpm) Max. Flow  

Faucets with Hot and Cold Water Supply

HOT 

SUPPLY

COLD 

SUPPLY

1-1/2” (38 

mm) MAX. 

DECK 

THICKNESS

SPOUT

O-RING

1-3/16” (30 mm) MIN. 

DIA. HOLE REQUIRED

GASKET

RETAINER

NUT

13” (330 mm)  

LONG FLEX HOSE

MIXING LEVER 

(Can Be Set and 

Removed)

TEMPERED 

SUPPLY

SPOUT

O-RING

1-3/16” (30 mm) MIN. 

DIA. HOLE REQUIRED

GASKET

RETAINER

NUT

13” (330 mm)  

LONG FLEX HOSE

1-1/2” (38 

mm) MAX. 

DECK 

THICKNESS

If a connection to separate 

hot and cold water supplies 

is desired, then a Bak-Chek

®

 

tee fitting (not supplied) must 

be used prior to connecting 

to the faucet.

EAF-250 Series

Battery Powered, Sensor 

Activated Lavatory Faucets

EAF-200 Series

Adapter Powered, Sensor 

Activated Lavatory Faucets

EAF-275 Series

Solar Powered with Battery 

Backup Sensor Activated 

Lavatory Faucets

EAF-225 Series

Adapter Powered, Sensor Activated 

Lavatory Faucets with Temperature 

Indicating Illumination

(Models shown 
with ISM Integral 
Spout Mixer)

• 13 mm open end wrench or nut driver for faucet retainer nut

• 3/4” open end wrench for female end of flex hose

TOOLS REQUIRED FOR INSTALLATION

Prior to installing the Sloan Optima EAF-275/EAF-250/EAF-200/EAF-225 Series Faucets, 

install the items listed below. Also, refer to rough-in illustrations.
• Lavatory/sink
•  Drain line
•  Hot and cold water supply lines or pre-tempered water supply line

Important:
•  ALL PLUMBING SHOULD BE INSTALLED IN ACCORDANCE WITH APPLICABLE 

CODES AND REGULATIONS.

•  FLUSH ALL WATER LINES PRIOR TO MAKING CONNECTIONS.
•  KEEP THREAD SEALANT OUT OF YOUR WATERWAY TO PREVENT COMPONENT 

PART DAMAGE! DO NOT USE ANY SEALANT ON COMPRESSION FITTINGS.

Trim Plates

When the EAF Faucet is installed on a sink that has three (3) hole punchings, a Trim Plate 

should be used. 

Trim Plates must be specified and ordered separately.

ETF-312-A Trim Plate for 4” (102 mm) Centerset Sink
ETF-510-A Trim Plate for 8” (203 mm) Centerset Sink

PRIOR TO INSTALLATION

FAUCET VARIATIONS

-DPU     

Drain Pop Up (EAF-200/225/250 Series)

-P

 

Plug-in Transformer/Adapter (EAF-200 Series)

-LT

 

Less Transformer/Adapter (EAF-200 Series)

*EAF-225 Series Faucets are furnished with a 1.5 gpm (5.6 Lpm) spray head

Summary of Contents for Solis EAF-275 Series









Reviews: