5
INSTALLATION INSTRUCTIONS
Step 1 — Unpack Scrub Sink
Carefully remove Sink from its protective carton. Examine the carton for additional
parts before discarding packaging material.
Step 2 — Remove Access Panel (2000 Series Sinks Only)
Remove Access Panel from Sink by lifting up and pulling outward on the handle
located at the bottom of the Access Panel. Refer to Figure 2. Do not use excessive
force. The Access Panel is not attached to the Sink with any fasteners. For double and
triple station sinks, remove all remaining Access Panels.
PRIOR TO INSTALLATION
Prior to installing the Sloan ESS-2000 or ESS-3000 Series Scrub Sink, install the
items listed below. Also, refer to Figures 1A through 1F.
• Electrical Receptacles for Plug-In Transformers (1 for each scrub station) —
Install Ground Fault Interrupt (GFCI) electrical receptacles for plug-in transformers
— 120 VAC, 2 amp service for each ETF-233 (24 VAC, 35 VA) plug-in
transformer used.
• Hot and cold water supply lines with supply stops or tempered water supply line
with supply stop
• Drain line
Important:
•
ADEQUATE STRUCTURAL SUPPORT IN OR BEHIND THE WALL IS REQUIRED.
REFER TO THE APPROPRIATE ROUGH-IN DIAGRAM ON PAGES 2 THROUGH 4 FOR
DRY WEIGHT OF SINK. STRUCTURAL SUPPORT MUST WITHSTAND WEIGHT OF
SINK WHEN FILLED WITH WATER.
•
ALL ELECTRICAL WIRING SHOULD BE INSTALLED IN ACCORDANCE WITH
NATIONAL/LOCAL CODES AND REGULATIONS.
•
ALL PLUMBING SHOULD BE INSTALLED IN ACCORDANCE WITH APPLICABLE
CODES AND REGULATIONS.
•
A 24 VAC STEP-DOWN TRANSFORMER MUST BE USED.
•
DO NOT PLUG TRANSFORMER INTO POWER SOURCE (RECEPTACLE) UNTIL ALL
WIRING IS COMPLETED. PERMANENT DAMAGE TO THE TRANSFORMER AND
CIRCUIT CONTROL MODULE WILL RESULT IF 24 VAC WIRES TOUCH EACH OTHER
OR SHORT WHEN POWER SUPPLY IS ACTIVE.
•
BEFORE CONNECTING FLEX HOSES TO SUPPLY STOPS, FLUSH ALL WATER LINES
UNTIL WATER IS CLEAR.
TOOLS REQUIRED FOR INSTALLATION
• Electric drill for drilling anchor holes.
• Screwdriver for installing “Z” clip fasteners.
• Socket or open end wrench for installing anchoring fasteners.
• Open end wrench for connecting water lines.
• Pipe wrench for installing drain line.
SCRUB SINK LOCATION
Determine the appropriate wall location for the Scrub Sink. Consider that hot and cold
water supply lines, a drain line, and an electrical source (receptacle) will be required.
Compare the physical dimensions of the Scrub Sink to the space available for the
installation. If wall is not load bearing, a carrier may be required behind the wall. Refer
to the appropriate Rough-in diagram on Pages 2 through 4, Figures 1A through 1F,
for Scrub Sink dimensions.
Prior to Scrub Sink installation, electric wiring, plumbing supply and drain must be
installed as illustrated in the Rough-in diagrams on Pages 2 through 4, Figures 1A
through 1F.
43¾” (1,111 mm)
FROM FLOOR
SURFACE TO CENTER
OF FASTENER HOLES
INSTALLER
FURNISHED
FASTENERS
OUTLINE OF
SCRUB SINK
DDOOUUBBLLEE SSTTAATTIIOONN SSIINNKKSS
TTRRIIPPLLEE SSTTAATTIIOONN SSIINNKKSS
CENTER Z-CLIP WITH
CENTERLINE OF SCRUB
SINK
Figure 3
SSIINNGGLLEE SSTTAATTIIOONN SSIINNKKSS
DDOOUUBBLLEE SSTTAATTIIOONN SSIINNKKSS
TTRRIIPPLLEE SSTTAATTIIOONN SSIINNKKSS
8” (203 mm)
FROM SIDE OF SINK TO
END OF Z-CLIP
C/L
OF
SINK
Z-CLIPS:
SSIINNGGLLEE SSTTAATTIIOONN — 2 Z-CLIPS REQUIRED
DDOOUUBBLLEE SSTTAATTIIOONN — 3 Z-CLIPS REQUIRED
TTRRIIPPLLEE SSTTAATTIIOONN — 3 Z-CLIPS REQUIRED
HANDLE
LIFT ACCESS PANEL
UP THEN OUTWARD
ACCESS PANEL
2000 SERIES
SCRUB SINK
Figure 2
1. LIFT
LATCH
UP
2. THEN SWING KNEE
ACTIVATED SOAP
PANEL UPWARD
3000 SERIES
SCRUB SINK
Figure 5
Step 3 — Install “Z” Clips to Wall (Figure 3)
Install “Z” Clips (using installer furnished fasteners) so that mounting holes measure
43¾ inches (1,111 mm) from floor surface for a standard 41 inch (1,041 mm) sink
height. Refer to Figure 3 for complete dimensioning details.
NOTE: Mounting height can vary to meet individual installation requirements. Adjust
all rough-in and mounting dimensions accordingly.
Step 4 — Mark Mounting Hole Locations on Wall
With the help of an assistant, carefully lift and hang the Scrub Sink onto the Z-clips.
Position Sink as required. Refer to Figure 4.
For 3000 Series Scrub Sinks, lift the Latch under the Knee Activated Soap Panel, then
lift Knee Activated Soap Panel to gain access to mounting holes. Refer to Figure 5.
Mark all four (4) Anchoring Hole locations using Sink as a template. Refer to Figure 6.
HANG SINK
ONTO Z-CLIPS
Figure 4
Z-CLIPS
USING SINK AS A
TEMPLATE, MARK
MOUNTING HOLES ON
WALL (2 HOLES ON
EACH SIDE OF SINK)
Figure 6
