SLEIPNER MOTOR AS Side-Power Automatic Main Switch Installation Manual Download Page 3

 3

5169

2

2020

-

It is the installers responsibility 

When installing Side-Power equipment to follow the outlined regulations/ classifi cation rules (electrical/ mechanical) according to 

international or special national regulations. Instructions in this guide cannot be guaranteed to comply with global electric/ mechanic 

regulations/ classifi cation rules.

To follow all health and safety laws in accordance with their local outlined regulations/ classifi cation rules. 

Before installation, it is important that the installer reads this guide to ensure necessary acquaintance with this product. 

The recommendations made in this manual are guidelines ONLY, and Sleipner Motor AS (Side-Power) strongly recommend that 

before installation, advice is obtained from a naval architect familiar with the particular vessel and regulations/ classifi cations.

    This manual is intended to support educated/ experienced staff  and is therefore not suffi  cient in all details for professional 

installation. 

(NB: These instructions are only general instruction. If you are not skilled to do this work, please contact professional 

installers for assistance.)

    All electrical work must be done by a licensed professional. 

Faulty installation of the tunnel, thruster or panel will render all warranty given by Sleipner Motor AS void.

MC_0038

MC_0273

Considerations and Precautions

EN

•  Install the automatic main switch as close to the battery(ies) as possible.

•  Do not connect the Sleipner automatic main switch with other products than appropriate original Sidepower control panels or other Sidepower control  

  devices. (NB: Sleipner products are specifi cally designed with a separate fi fth control cable for the automatic main switch.)

•  The automatic main switch must be installed so that it keeps dry at all times.

•  The automatic main switch can NOT be fi tted in spaces requiring Ignition protected equipment.

•  Ensure to use the correct fuse for the main switch depending on the thruster model installed.

IMPORTANT

This manual is to be used in addition to the regular installation manual for the Sidepower thruster. This manual is intended for professionals only.

Summary of Contents for Side-Power Automatic Main Switch













Reviews: