manualshive.com logo in svg

SLE SLE4000 Model B, Service Manual, Page: 117 / 328

Share
Download
SLE SLE4000 Model B Service Manual Download Page 117

(Model C)                                                                                                                                                    Page 117

14.15 Battery Charge Verification

Check that the battery has fully charged by checking the battery connector 
voltage is at least 13.7V when the unit is powered from the mains.

Acceptable tolerance:  >13.7 mbar.

Check list Item 15.

14.16 Battery Life Verification

After the battery has been fully charged (from the soak test), leave the unit in 
CMV mode at 80 BPM on the battery alone. 
Ensure the ”Main Power Fail” alarm is active.
Ensure that the ventilator runs for a minimum of 30 minutes before the “Battery 
low alarm” is activated. 
Ensure that the ventilator continues operation on battery for a further 15 minutes 
(minimum) after the battery low alarm first occurred. 

Check list Item 16.

14.17 Total Power Fail Alarm Test

Check the operation of the total power fail alarm by switching the mains switch off 
and, with the unit powered by the battery alone, half press the power off button 
(on the back panel). A continuous loud alarm should sound. Press the power off 
button in fully and the sound should cancel.

Check list Item 17.

Summary of Contents for SLE4000 Model B









































































































































































































































































































































Reviews:

No comments