background image

UG337: Si53208-EVB User’s Guide

8-Output PCI-Express Gen1/2/3/4 and SRIS Clock Buffer Evalua-
tion Board

This document describes operation of the Silicon Laboratories Si53208-EVB evaluation
board. It’s designed to evaluate the Si53208, 8-output PCI-Express Gen1/2/3/4 which
is an SRIS Clock Buffer. Selector switches make it easy to select the voltage for both
core and IO supplies. Jumpers allow for easy static configuration of the control inputs
as well as provide a port for external test equipment access. Similarly, each regulated
supply can be bypassed and driven externally for either precise voltage control or for
measuring PSRR performance. Convenient probe pads and isolation resistors permit
on-board single-ended or differential measurements. Finally, the PCB layout optimizes
signal integrity and skew which rounds out the capabilities of this EVB.

KEY FEATURES

• Evaluation of Silicon Labs Si53208
• External power or USB powered
• DC-coupled differential output clocks
• DC-coupled differential input clock
• Switchable voltage settings
• Easy manual configuration via jumpers
• Easy current measurement

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com

1

Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 26, 2021

1

Summary of Contents for Si53208















Reviews: