SkyWave IDP 800 Series Hardware Manual Download Page 10 | Manualshive

Page: 10 / 102

SkyWave IDP 800 Series Hardware Manual Download Page 10

IDP 800 Terminal Series - Hardware Guide

T209, Version 01 x © SkyWave Proprietary

CAUTION

Under no circumstance should you recharge Energizer

®

Ultimate

Lithium batteries. Severe personal injury, death, or substantial
property damage is possible.

CAUTION

Always follow local disposal guidelines when disposing of
lithium batteries. Refer to the manufacturers' website (

safety datasheet

) for information on proper disposal of lithium

batteries.

CAUTION

Do not short circuit or expose batteries to temperatures above the
maximum rated temperature as specified by the manufacturer.
Do not puncture or crush.

Product Safety Datasheets

Refer to the manufacturers' website for specific battery details and safety precautions,
including handling and shipping.

Energizer Non-rechargeable Lithium Iron Disulfide (Li/FeS

2

):

http://data.energizer.com/Static.aspx?Name=AppManuals

http://data.energizer.com/Static.aspx?Name=ProductSafety

Tenergy Rechargeable Nickel Metal Hydride (NiMH):

http://www.onlybatterypacks.com/up/pdf/msdsdatasheets/TENERGY%20MSDS-
%20NIMH.pdf

http://www.tenergy.com/10321_datasheet.pdf

Safety Disclaimer

SkyWave makes no warranties, representations or guarantees that the products and
network services are suitable for any use in any hazardous environments requiring fail
safe performance (including without limitation marine safety and distress systems,
operation of nuclear facilities, aircraft navigation or communications systems, weapons
systems, air traffic control and life support services) or any other application in which the
failure of the products or network services could result in death or personal injury.
Solution Providers assume all liability associated with selling any products and network
services for any such applications, and Solution Provider will defend, indemnify, and
hold SkyWave harmless against any claims against SkyWave for loss, damage, liability,
or expense (including lawyers’ fees) arising out of or related to the sale by Solution
Providers or any Solution Provider Reseller, or the user by any end user, of any product
or network service.

Please read all cautions and warnings throughout this document.

Safety Precautions

The mobile device must comply with all safety precautions relating to the operation,
usage, service and repair of the terminal. SkyWave assumes no liability for the
customer’s failure to comply with any of these precautions.

Caution warnings appear throughout this document.

«
...
8
9
10
11
12
...
»

Summary of Contents for IDP 800 Series







































































































Reviews:

No comments