Skymsen LI-2,0-N Instruction Manual Download Page 3

3

1. INTRODUCTION    

1.1 Safety

When incorrectly used this equipment is a potentially DANGEROUS machine. Maintenance, 
cleaning or any other service shall be performed by a duly trained person and with the 
machine unplugged. 

To avoid accidents respect the following instructions :

1.1.1 Read all the instructions.

1.1.2 In order to avoid the risk of electric shocks and damage to the machine, never operate 
it wearing wet clothes or shoes, install the equipment on a wet or humid surface nor dip it 
in water or any other liquid, and do not spray water directly on it.

1.1.3 The use of the equipment must be always supervised specially when used next to 
children.

1.1.4 Before cleaning and when not in use or before inserting or removing accessories, 
maintenance, or other services, disconnect machine from power source.

1.1.5 – Do not use the equipment if the cord or the plug is damaged. Do not leave the 
electric cable on the edge of the table or counter nor let it touch hot surfaces.

1.1.6 Do not use the equipment if it is not working correctly, nor if it has been damaged in 
any way. In case that happens, take the equipment to the nearest Technical Assistance to 
check it up.

1.1.7 The use of accessories not recommended by the manufacturer may cause personal 
hurt.

1.1.8 Keep your hands or any tool out of the machine while operating to avoid personal 
hurt or any damage to the equipment.

1.1.9 During operation, never wear loose clothes with wide sleeves principally around the 
wrists.

1.1.10 – Make sure the equipment voltage and the network voltage are the same, and the 
equipment has been solidly grounded.

1.1.11 – Knife has sharp edges, handle it with care

1.1.12 – Always place the Lid # 02 (Pic.01) on the cup before to start the machine,

Summary of Contents for LI-2,0-N

























Reviews: