12. CUSTOMER SERVICE
13. ACCESSORIES
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:[email protected]
http://www.skylinkhome.com
P/N. 101Z697
Patent Pending
©2010 SKYLINK GROUP
10. FCC
The Remote Control is approved by the FCC and it complies with Part 15 of the
FCC Rules. Its operation is subject to the following two conditions :
1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible
of compliance could void the user’s authority to operate the equipment.
TM
The SkylinkHome System consists of many other devices such as
TM
SkylinkHome Remotes, Motion Sensor, ON/OFF Wall Switch, Wall
Dimmer, Plug-In Dimmer with or without Repeater, Plug-In ON/OFF
Control (Outdoor/Indoor), Screw-In Dimmer, ON/OFF/Dimming Control,
TM
ON/OFF Control, Smart Button Garage Door Control, etc. Please visit
Skylink website at www.skylinkhome.com for more information.
V1.8
9. BATTERY
When the operating range is reduced, or when the red LED does not
flash during operation, it is time to replace the battery. Follow the same
procedure as installing the battery in section 1 of this manual to replace
the battery.
Note: Dispose of old batteries promptly and properly.
8. PASSWORD PROTECTION (CONT)
11. WARRANTY
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
Note:
1. During password input or programming, if you press the wrong
button, start over again after you see three flashes from LED or
after 10 seconds.
2. Press button only after LED finishes flashing.
3. The interval between two presses should not be more than 10
seconds.
4. Key 10 can be used as one digit in the password.
The factory default password:
TC-318-7: [1, 2, 1, 2]
TC-318-10: [2, 5, 2, 5]
TC-318-14: [2, 5, 2, 5]
You can assign your personal password; the password [PWD] can be
2-6 digits long.
To enable password protection, follow the steps below:
1. Press [ ] immediately after holding [ ], the LED flashes twice
then goes off;
2. Input [PWD], after the LED goes off, press [ ]. After LED flashes
twice and goes off, the password is enabled.
To disable password protection, follow the steps below:
1. Press [ ] immediately after holding [ ], the LED flashes then
goes off;
2. Input [PWD], after the LED goes off, press [ ]. After LED flashes
twice and goes off, the password is disabled.
To change password, follow the steps below:
1. Press [ ] immediately after holding [ ], the LED flashes twice
then goes off;
2. Input old [PWD];
3. After LED goes off, input new [PWD];
4. Press [ ];
5. After LED goes off, input new [PWD] again;
6. Press [ ]
7. After LED flashes twice and goes off, the password is changed.
If you forget your password and want to restore the factory default
password, follow the steps below:
1. Slide out the battery door;
2. Hold the "PROG" button on the back and slide back the battery door.
3. When the front LED flashes quickly, release the button.
After the unit is reset to factory default, it can not control any receiver until
you reprogram it to receivers you want to control.
If you lost a remote, to ensure security and safety, you should erase all
remotes from all receivers and reprogram all existing remotes. Please
refer to the erasing method of each receiver.
If you would like to
-
find out the up-to-date specifications
-
know more about features and applications
-
download documents, i.e. user’s instructions
-
order Skylink products
or if you have difficulty getting products to work, please:
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at [email protected], or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax (800) 286-1320
