10. To Reset the Pin Code to Factory Default
10. To Reset the Pin Code to Factory Default
9. To Change the Keypad Pin Code After Initial Setup
9. To Change the Keypad Pin Code After Initial Setup
11. Installing the Garage Door Keypad
11. Installing the Garage Door Keypad
15. ISED
15. ISED
14. FCC
14. FCC
16. One Year Warranty / Customer Service
16. One Year Warranty / Customer Service
13. FAQ
13. FAQ
12. Replacing the Battery
12. Replacing the Battery
1. Enter the old pin code plus * [PIN *].
a.
Example, 1234*.
2. Enter the new pin code from 2 to 8 digits plus *, twice.
a.
Example, 5678* and again 5678*.
3. Do not press the learn button on the operator. The
keypad is already programed to the operator and this
step is not required.
4. To open and close the door, press the new pin code plus
# [PIN #].
a.
Example, 5678 # for single door.
5678 # 1 for multiple door.
If you forget your pin code, to reset the pin code:
1. Remove the battery.
2. While the battery is out, hold [*] and [#] buttons together.
3. While holding both buttons put the battery back in.
4. Keep holding both buttons for about 5 seconds until you
hear a long beep.
This resets the pin code back to 0000.
5. Because the keypad has been reset, follow Sections 3-7
for initial setup and to program the keypad to the
operator.
1. Undo the screw (1) on
the bottom side of the
keypad (A) and remove
the back plate.
2. Insert an AAA battery.
3. Mount the back plate
(B) with the mounting
accessories (2).
4. Attach the keypad on
the back plate and
tighten the screw (1) on
the bottom of the
keypad.
1.5 volt Alkaline type
(AAA size) battery
required. Please refer
to Section 12 on how to
insert the battery.
1.5 volt Alkaline type
(AAA size) battery
required. Please refer
to Section 12 on how to
insert the battery.
(1)
(A)
(2)
(1)
(B)
(1)
When the operation range is reduced, or when the
backlight LED does not flash during operation, it is time to
replace the battery.
1. Undo the screw (1) on the back plate of the keypad.
2. Pry out the back plate from the keypad.
3. Take out the old battery (2) from the keypad.
4. Place the new battery (2) in position. Beware of the
polarity.
5. Close the back plate and re-insert the screw (1).
RISK OF EXPLOSION IF BATTERY IS REPLACED BY
AN INCORRECT TYPE. DISPOSE USED BATTERIES
ACCORDING TO MANUFACTURER'S INSTRUCTIONS.
RISK OF EXPLOSION IF BATTERY IS REPLACED BY
AN INCORRECT TYPE. DISPOSE USED BATTERIES
ACCORDING TO MANUFACTURER'S INSTRUCTIONS.
(1)
(2)
The door opener does not react after I press the button
on the keypad transmitter.
A. Ensure you hear 3 beeps from the keypad transmitter
after entering--
[Password] [#]
OR
[Password] [#] [Door Number]
--for multiple door operation. If you don’t hear 3 beeps
that means you have entered the incorrect password.
Re-enter the password.
Ensure the keypad transmitter has been programmed to
the Smart Button™ or garage door opener. Refer to
Sections 3-8 on how to program a keypad to the receiver.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) This device must
accept any interference received, including interference that
may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This device is a license-exempt transmitter/receiver that
complies with Innovation Science and Economic Develop-
ment Canada's license-exempt RSS(s). Operation is subject
to the following two conditions:(1) This device may not cause
interference, and (2) This device must accept any
interference, including interference that may cause undesired
operation of the device.
P/N:101Y106-003
This product is guaranteed to be free of defects in materials
and workmanship for 1 year from the date of purchase. If this
product is defective, call 1-800-304-1187 for repair or
replacement parts. Guarantee does not include normal wear
and tear or batteries.
If you have any questions, problems or missing parts,
please call Skylink Customer Support:
1-800-304-1187
9:00 AM – 5:00 PM EST, Monday-Friday
Or e-mail us at
www.skylinkhome.com
