SkyLink KN-1 Installation Instructions Download Page 2

The keypad can operate multiple garage doors 

(Additional Smart Button™ is required for multiple 

garage doors operation).
To enable the multiple-door operating mode:
1.  Enter the current password (factory default [0 0 0 

0]), then press [*]. 

2.  Press [9] [#], you will hear 2 beeps to confirm you 

have enabled the multiple-door operating mode.

To disable the multiple-door operating mode:
1.  Enter the current password (factory default [0 0 0 

0]), then press [*].

2.  Press [0] [#], you will hear 2 beeps to confirm you 

have disabled the multiple-door operating mode.

SECTION 4 – MULTIPLE GARAGE DOORS OPERATION

SECTION 4 – MULTIPLE GARAGE DOORS OPERATION

SECTION 5 - OPERATION

SECTION 5 - OPERATION

Single Door Operation:
1. Press the pin code plus [#].
Example: 0 0 0 0 #
Multiple Doors Operation:
1. Press the pin code plus [#] plus [Door No.]
Example, Door1: 0 0 0 0 # 1
Door 2: 0 0 0 0 # 2
Door 3: 0 0 0 0 # 3
Door 4: 0 0 0 0 # 4

1.  Undo the screw on the bottom side of the keypad 

and remove the back cover. 

2.  Insert a AAA battery.
3.  Mount the back cover with the mounting accesso-

ries (provided). 

4.  Attach the keypad on the back cover and tighten 

the screw on the bottom of the keypad.

SECTION 9 – INSTALLING THE KEYPAD

SECTION 9 – INSTALLING THE KEYPAD

  One 1.5V Alkaline Type (AAA size) battery (sold 

separately) required for the keypad.

1.  Undo the screw on the bottom side of the keypad. 
2.  Pry out the keypad from the back cover.
3.  Take out the old battery from the keypad.
4.  Place the new battery in position. Beware of the 

polarity.

5.  Attach the keypad on the back cover and tighten 

the screw on the bottom of the keypad.

SECTION 10 – REPLACING THE BATTERY IN THE KEYPAD

SECTION 10 – REPLACING THE BATTERY IN THE KEYPAD

  When the operating range is reduced, or when the 

backlight LED does not flash during operation, it is 

time to replace the battery.

You can add on up to 16 additional transmitters to 

control the same Smart Button™. Skylink offers 

keychain transmitters and visor transmitters to work 

with your Smart Button™. For more information, please 

visit our website SKYLINKHOME.COM or contact us.

SECTION 11 – ADDITIONAL TRANSMITTER

SECTION 11 – ADDITIONAL TRANSMITTER

Q:  The Smart Button™ does not respond to the 

keypad.

A:  You must program the keypad to the Smart Button

™ before they can work together.

 

Ensure you hear 3 beeps from the keypad after 

entering:

 

[Password] [#] or

 

[Password] [#] [Door Number]

-  Ensure that the wires that were initially connected 

to the original wall button are not loose.

Q:  Can I erase just one keypad from the 

Smart Button™?

A:  You must erase all the devices in the 

Smart Button™ and then program the ones you 

want to keep.

Q:  The LED on the Smart Button™ turns on but does 

not flash after the Smart Button™ has been 

connected.

A:  Add a 12VDC, 100mA adapter (sold separately) to 

the Smart Button™.

SECTION 12 – FAQ

SECTION 12 – FAQ

  To erase the unwanted remote from the Smart 

Button™, first you must erase all the remotes, then 

program the ones you want to keep.

How to reset the password if you forget the PIN code.
1.  Remove the battery.
2.  Press and hold [*] and [#] buttons at the same time.
3.  Keep holding both buttons and put the battery back 

in.

4.  Keep holding both buttons for about 5 seconds until 

you hear a long beep. This resets the pin code back 

to 0000.

5.  Because the keypad has been reset, follow Section 

3 to program the keypad to the Smart Button™.

SECTION 8 – RESET PASSWORD IN KEYPAD

SECTION 8 – RESET PASSWORD IN KEYPAD

1.  Press and hold the learn button for approximate 10 

seconds..

2.  The LED will flash quickly after 10 seconds to 

indicate all the programmed remotes have been 

erased.

3.  Release the learn button.

1.  Enter the current PIN, (factory default PIN 0 0 0 0), 

press *.

2.  Enter new 2 to 8 digit PIN, press *.
3.  Enter new PIN again, press *.
 

For example, if you are changing the PIN number 

from 0000 to 123456, enter the following sequence, 

0000, *, 123456, * , 123456, * .

 

If confirmed, the backlit LED flashes and the unit 

emits a long beep.

SECTION 7 – CHANGE PASSWORD IN KEYPAD

SECTION 7 – CHANGE PASSWORD IN KEYPAD

SECTION 6 - ERASING REMOTE FROM THE SMART BUTTON™

SECTION 6 - ERASING REMOTE FROM THE SMART BUTTON™

  The factory default setting is Single Door Operation 

Mode.

 

If after installing the Easy Clip™ you want to re-install 

the Smart Button™ to another place, then open the 

“Easy Clip™ ” by gently unlocking the two buckles with a 

screw driver and remove it from the wires. Do not re-use 

the Easy Clip™. Refer to Section 1, Step 6 to re-install it.

1.  Power up the garage door opener. The red LED on 

the Smart Button™ should continue to flash.

2.  If the red LED does not flash 

after connected to your garage 

door opener for 2 minutes, 

your existing garage door 

opener is probably too old. 

Plug in an adapter (purchase 

separately) to power up the 

Smart Button™.

Rating of plug in adapter: 

12VDC 100mA, 3.5mm DC 

plug.

3.  Secure the Smart Button™ 

with the double-sided tape.

SECTION 2 – POWER UP THE SMART BUTTON™

SECTION 2 – POWER UP THE SMART BUTTON™

In order to operate the Smart Button™ 

remotely, you must program the 

keypad to the Smart Button™ in order 

for the two communicate. Each Smart 

Button™ can be operated by up to 16 

different keypad or transmitters.
1.  Press and release the learn button 

on the side of the Smart Button™. 

2.  The red LED will flash quickly for 

30 seconds.

3.  Enter the default PIN [0 0 0 0] [#] 

(or [0 0 0 0] [#] [Door 

Number] for 

multiple door operation) on the 

keypad within 5 seconds.

4.  The red LED in the Smart Button™ 

will return to the slow flash once the 

keypad is programmed.

5.  You may now operate the garage 

door opener with the keypad.

SECTION 3 – PROGRAMMING

SECTION 3 – PROGRAMMING

 

Do not cut the antenna wire. Straighten up the antenna 

wire to improve the signal reception.

LED

Learn Button

Antenna

Antenna

Reviews: