If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
11. WARRANTY
If the connector is placed on the top and middle posts, that column is
set on “ + ” . If the connector is placed on the middle and bottom posts,
that column is set on “ - ”. If the connector is removed completely,
(not placed on any posts), it is set to
“ 0 ”. (see diagram for examples of
how to set a column to the three
different positions). When removing
a connector to set a column to “ 0 ”,
save the connector in case you
change the code at a later date.
After setting up the code connectors on the keypad transmitter,
you are ready to set the same code on the receiver.
Remove the screw that holds
the connector cover, and remove
the cover.
You will see 10 connectors. The settings must match with those of
the transmitter.
5. KEYPAD OPERATION
8. ADDITIONAL TRANSMITTER
9. CAUTION
10. FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
3
4
5
6
Connectors
1 to 10 are
the same.
NOTE:
The backlight comes on and a beep is emitted when any key is pressed.
The backlight of the keypad may not be visible when it is too bright
outside. When any key is pressed, the next key must be pressed within 5
seconds or the backlight turns off and the sequence is cancelled. You
must begin again.
If the keypad does not emit a beep when pressed, wait a few seconds
and press the key again.
6. CHANGE PIN
Follow the instructions below to change the PIN.
To change your PIN:
1. Enter the current PIN, (factory default PIN 0 0 0 0), press ,
2. Enter new 4 digit PIN, press ,
3. Enter new PIN again, press .
For example, if you are changing the PIN number from 0000 to
1234, enter the following sequence, 0000, ,1234, ,1234, .
If confirmed, the backlit LED flashes and the unit emits a long beep.
*
*
*
*
If you do not hear 3 beeps after the 4-digit PIN and [#] is entered,
that means you have entered an incorrect PIN, and the keypad transmitter
will not operate your garage door.
*
*
Two 3 volt Lithium type (CR2032) batteries (included).
It is time to change
the batteries when
the backlight no
longer appears.
+
-
Battery Compartment
7. BATTERY
You can now mount the transmitter on a
desired location.
Lift up the cover and insert screw
above the keypad in the slot provided (a).
Remove the battery cover and insert
the second screw in the lower slot (b).
Tighten all screws. Replace the battery
cover, insert and tighten screw (c).
(a)
(c)
(b)
9
7
Put the cover and screw back onto the receiver. Plug the receiver
into an electrical outlet.
Enter [0,0,0,0] [#] will open the garage door.
8
Remove the receiver from the electrical outlet before
changing the code.
WARNING
RISK OF ELECTRICAL SHOCK. FOR INDOOR USE ONLY.
CAUTION : DISCONNECT POWER BEFORE CODE CHANGING.
REPLACE COVER AFTER CODE CHANGING.
Maximum Rating:
Input : 120VAC 60Hz 2W
‘+’
‘-’
‘
0
’
12. CUSTOMER SERVICE
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:[email protected] (Reply within 24 hrs)
http://www.skylinkhome.com
P/N. 101A207-003 Rev.3
©2003 SKYLINK GROUP
If you would like to order Skylink’s products or have difficulty getting them to work,
please :
1. visit our FAQ website at www.skylinkhome.com, or
2. email us at [email protected] (reply within 24 hrs), or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax +800 286-1320
4. CHANGE THE OPERATION CODE FOR
BOTH TRANSMITTER AND RECEIVER (BOTH)
2
You can randomly remove some
connectors, leaving some in place.
A connector can be removed with
the clip, as shown.
You can add as many additional transmitters as you
want to control the same receiver. Simply set the
same operation code on all transmitters with the same
code setting on the receiver. Houselink
®
offers
Keychain Transmitter Model 318TN and Keyless Entry
Transmitter Model 318K to work with your receiver.
For more information, please visit our website at
www.skylinkhome.com or contact us.
