8. OTHER HOUSEHOLD ALERT
®
SENSORS
The Household Alert
®
receiver can work with up to 4 different sensors:
garage door monitor sensors, door / window sensors, water sensors,
indoor/outdoor motion sensors, etc. Please visit www.skylinkhome.com
or contact us at [email protected] for more information of how
to fully utilize your Motion Alert.
9. WARRANTY
If, within one year from date of purchase, this pro duct should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
If you would like to order Skylink’s products or have difficulty getting them to work,
please :
1. visit our FAQ website at www.skylinkhome.com , or
2. email us at [email protected]
10. CUSTOMER SERVICE
CAPITAL PROSPECT LTD.
Rm.1303, 13/F, Block B, Veristrong Ind. Centre,
36 AuPuiWan Street, Fo Tan, Hong Kong
Tel: +852 2602-1318 Fax: +852 2602-4684
Email:[email protected]
http://www.skylinkhome.com
P/N. 101A259-001 Rev.1
©2005 SKYLINK GROUP
You should walk in the area that you would like the sensor to monitor. The
receiver will beep if the sensor detects your movement. If the receiver
does not respond, adjust the mounting angle accordingly. Perform the
walk test again after 30 seconds. Repeat this procedure until your motion
is detected. There should be no movement in the detected area during the
30 seconds.
Perform walk test in the undesired area to ensure movement cannot be
detected.
Tips: The sensor should not face towards direct sunlight, placing near
heat or cold producing devices (i.e. A/C or furnance vents, fans, ovens,
heaters etc.) that may cause false triggers.
12º
When motion is detected in the monitored area, the sensor will send a
signal to the receiver. It will beep and the corresponding zone red LED
will flash for 15 seconds.
If the sensor is set to zone 1, zone 1 red LED on the receiver will flash,
and the receiver will emit a continuous “single beep”, i.e. “beep” pause,
“beep”, pause….. etc.
If the sensor is set to zone 4, zone 4 red LED will flash, and the receiver
will emit a continuous “4 beeps”, i.e. “beep beep beep beep” pause
“beep beep beep beep” pause ……etc.
By the number of beeps emitted by the receiver, user can identify
which zone is triggered.
4. OPERATION
5. BUZZER VOLUME
You can select the buzzer volume by
switching the volume switch to “HI” or
“LO” position.
The buzzer can be disabled by switching
to the “OFF” position.
6. MUTE
When the battery level on the sensor drops to a certain level, or the
sensor is out of the operating range, the receiver will show a “loss of
signal” indication. The red LED representing that zone will flash rapidly,
i.e. if zone 1 sensor is lost, the zone 1 red LED will flash rapidly.
When the loss of signal indication occurs, move the receiver closer to the
corresponding sensor and trigger that sensor. If the red LED stops flash-
ing rapidly, that means the receiver or sensor needs to be relocated. If the
“loss of signal” indication persists, replace the battery of that sensor.
7. LOSS OF SIGNAL INDICATION
When a sensor is triggered for a long period of time, you may stop the
buzzer by pressing the mute button. When another signal comes again,
you can disable the buzzer for all currently activated sensors by pressing
the mute button. The receive will beep again if it receives another signal.
For instance, if you are working in your
garage, you may want to disable the
buzzer for this garage only. Then you can
press the “Mute” button after it starts to
sound. If any other sensor is triggered,
the receiver will sound again.
3. POWER UP THE HOUSEHOLD ALERT
®
RECEIVER AND INDOOR/
OUTDOOR MOTION SENSOR (CONT)