Operation
3. OPERATION
Push Button
Press the push button to open or close the garage door.
Lock Button
Lock feature is designed to prevent Skylink
®
remotes
such as Skylink
®
Keychain Remote Model 4B-201
to operate the garage door opener.
To activate the lock feature
1. Press and hold the lock button for approx. 2 seconds, then release it.
2. When the lock feature is activated, the red LED underneath the push
button will flash rapidly.
Note: If a valid wireless remote signal is received while the lock feature is
activated, Garage One
TM
will beep to reminding you the Garage One
TM
is
locked.
Push button
Timer / Learn LED
Loss of Signal LED
Learn button
Lock button
3. OPERATION (CONT)
Chamberlain
®
, Lift-Master
®
, Sears Craftsman
®
Multi-Function
Wall Console
There are 3 buttons on the Multi-Function Wall Console:
1) Push Button - Open / Close garage door.
2) Lock Button - Enable / Disable handheld remotes to operate the garage
door opener.
3) Light Button - Turn on / off light.
Skylink
®
Garage One
TM
also has 3 buttons, their functions are identical to
the Chamberlain
®
/ Lift-Master
®
/ Sears Craftsman
®
wall console.
Chamberlain
®
/ Lift-Master
®
/
Function
Equivalent button on
Sears
®
Skylink
®
Garage One
TM
Push Bar
Open / Close door
Push Button
Lock Button
Lock Button
Light Button
Turn light on / off
Learn Button
Enable / Disable operation
from handheld remotes
Antenna
Prevents operation
from handheld remotes
Turn light on / off
Open / Close door
Chamberlain
®
Keychain Remote
The upper left button on the keychain remote (Button 1) has been pro-
grammed to the receiver at the factory. Pressing this button will activate
the receiver therefore open / close the garage door. If you would like to
add more keychain remote, follow the procedures below.
Button 1
Learn Button
To program Skylink’s remote control / sensor
1. Press the learn button for approx. 5 seconds.
2. The “Timer / Learn” red LED will be on, release the learn button.
3. Activate the Skylink
®
remote control. If the Skylink
®
remote control has
multiple buttons, press the button you would like to operate.
4. The “Timer / Learn” LED will be off after it has successfully programmed
the remote control.
5. You can now press the programmed remote to operate the garage
door opener.
Erase Skylink
®
remote controls / sensors
To erase unwanted remote control(s), first erase all remote controls and
sensors, then program the ones you would like to keep.
Erase all remote controls / sensors
1. Press and hold the learn button for 15 seconds.
2. The “Timer / Learn” red LED will flash rapidly meaning all remote have
been erased.
3. You have now successfully erased all the remote controls and sensors.
Follow the instructions “To program Skylink’s remote control” to add the
remote control(s) you would like to keep.
The battery of the keychain remote (Alkaline, Type 23A, 12V) needs to
be replaced when either one of the followings occurs:
1. The LED on the keychain doesn’t flash or on when a key is pressed; or
2. The operating range starts to decrease.
To replace the battery:
1. Undo the two screws on the back of the
transmitter.
The bottom case will then come off.
2. Using a small screwdriver or pen, pry out
the old battery from one end.
3. Place the new battery in position. A diagram
in the battery compartment indicates which
end is positive and which is negative.
4. Close the battery cover and reinsert
two screws.
+
-
4. BATTERY
To deactivate the lock feature
1. Press and hold the lock button for approx. 2 seconds, then release it.
2. When the lock feature is deactivated, the red LED underneath the
push button will flash slowly indicating the Garage One
TM
is in normal
operating mode and the lock feature is deactivated.