Skylab SKB369 Manual Download Page 18

 

Skylab M&C Technology Co., Ltd 

 

 

 

 

   

Module SKB369                 

 

 

 

 

 

                                                                                                                                     

SKB369-DA-001,A/1 

15.

 

Contact Information

 

Skylab M&C Technology Co., Ltd.

 

深圳市天工测控技术有限公司   

 

Address:

 

6 Floor, No.9

 

Building, Lijincheng

 

Scientific & Technical

 

park, Gongye

 

East

 

Road,

 

Longhua

 

District, Shenzhen, Guangdong, China

 

Phone: 86-755 8340 8210(Sales Support)

 

Phone: 86-755 8340 8510(Technical Support)

 

Fax: 86-755-8340 8560

 

E-Mail: [email protected]

 

Website: www.skylab.com.cn        www.skylabmodule.com

 

Bluetooth Module

FCC Radiation Exposure Statement
The modular can be installed or integrated in mobile or fix devices only. This modular
be installed in any portable device, for example, USB dongle like transmitters is forbidden.
This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be collocated or operating in conjunction with
antenna or transmitter.
If the FCC identification number is not visible when the module is installed inside another
device, then the outside of the device into which the module is installed must also display
label referring to the enclosed module.
This exterior label can use wording such as the following:
“Contains Transmitter Module FCC ID:2ACOE-SKB369 Or Contains FCC ID:2ACOE-SKB369
when the module is installed inside another device, the user manual of this device must
contain below warning statements;
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
The devices must be installed and used in strict accordance with the manufacturer's
instructions as described in the user documentation that comes with the product.

This device is intended only for OEM integrators under the following conditions:

1) The antenna must be installed such that 20 cm is maintained between the antenna
and user.
2) The transmitter module may not be coÿlocated with any other transmitter or
antenna. Module Antenna Type: PCB ANT, 1dBi gain

Summary of Contents for SKB369



















Reviews: