manualshive.com logo in svg

Skyjack 3219 SJIII Compact Series, Operating Manual

Share
Download
Skyjack 3219 SJIII Compact Series Operating Manual Download Page 20

It is the responsibility of the operator to read, completely understand and follow all instructions and warnings 

contained in this operating manual and on the aerial platform.

2.3-6  Battery Tray Side

•  Pothole Protection Device

 -

Ensure mechanisms have no sign of 
visible damage and are free from dirt and 
obstructions.

•  Battery Tray

 -

Ensure tray latch is secure and in proper 
working order.

•  Battery Charger

(SJIII 3219 - Entrance Side)

 -

Ensure charger is secure and shows no 
visible damage.

•  Battery

 

Proper battery condition is essential to 
good performance and operational safety. 
Improper fluid levels or damaged cables and 
connections can result in component damage 
and hazardous conditions.

WARNING

Explosion hazard. Keep flames 
and sparks away. Do not smoke 

near batteries.

WARNING

Battery acid is extremely corrosive - 
Wear proper eye and facial protection as 
well as appropriate protective clothing. 
If contact occurs, immediately flush with 

cold water and seek medical attention.

1.  Check battery case for damage.

2.  Clean battery terminals and cable ends 

thoroughly with a terminal cleaning tool or 
wire brush.

3.  Ensure all battery connections are tight.

4.  If applicable, check battery fluid level. If plates 

are not covered by at least 1/2" (13 mm) of 
solution, add distilled or demineralized water.

5.  Replace battery if damaged or incapable of 

holding a lasting charge.

WARNING

Use original or manufacturer-approved 
parts and components for the aerial 

platform.

Pothole Protection Device

Battery Tray

Battery 
Charger

Battery

Battery Tray

Hydraulic/Electric 
Tray

Battery

Fuse Box

Battery 
Charger

SJIII 3226 & 4632

SJIII 3219

FAMILIARIZA

TION

FAMILIARIZA

TION

Page 20

SJIII DC Electric

Visual & Maintenance Inspection 

Section 2 - Familiarization

Summary of Contents for 3219 SJIII Compact Series









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands