Touch panel work as DMX512 master
Touch Panel work as RF remote
Use the controller’s Match key
Match
:
Short press match key, immediately press zone
key of the touch panel.
The LED indicator fast flash a few times
means match is successful.
Use Power Restart
Match
:
Switch off the power of the receiver, then switch on power again,
immediately short press zone key 3 times on the touch panel.
The light blinks 3 times means match is successful.
.
Delete
:
Switch off the power of the receiver, then switch on power again,
immediately short press zone key 5 times on the touch panel.
The light blinks 5 times means all matched remotes were deleted.
Delete
:
Press and hold match key for 5s to delete all match,
The LED indicator fast flash a few times
means all matched remotes were deleted.
Touch panel 4 zone remote can match with RF controller for
single color, dual color(WW/CW), RGB, RGBW
or RGB+CCT light type. End user can choose the suitable match/delete ways. Two options are offered for selection:
Touch panel work as RF remote
Note:
●
For single color, touch RGB/CCT wheel only change brightness, RGB, MODE, SPEED key is unvalid.
●
For dual color, touch RGB/CCT wheel only change color temperature, RGB, MODE, SPEED key is unvalid.
●
For RGB, when touch CCT wheel, adjust color temperature by mix R/G/B channel.
●
For RGBW, when touch CCT wheel, adjust W channel brightness.
●
Turn on key tone: Long press power key 10s
when all zone light is off,
will turn on or turn off tone.
Turn on/off all
zone
light.
RGB color / Color
temperature.
Press RGB or CCT key to switch between RGB wheel and CCT wheel.
Short press play 10 built-in dynamic mode, long press 2s run mode-cycle.
Short press turn on zone light and select zone simultaneously,
long press 2s turn off zone light.
4 zone control seperately or synchronously, each zone could control multiple receivers.
Only multiple zone have same light type can select synchronously.
ZONE
ZONE
ZONE
ZONE
MODE
SPEED
BRIGHT
SCENE
For dynamic RGB mode, adjust speed, short press 10 levels, long press 2s get the default speed.
For static RGB color, adjust saturation, namely change current static RGB color to mixed white slowly,
short press 11 levels, long press 1-6s for continuous 256 levels adjustment.
Adjust brightness, short
press
10
levels, long press 1-6s for continuous 256 levels adjustment.
Short press replay scene. Long press 2s to save the current color into the scene.
4 zone recall or save synchronously.
CCT
RGB color, 24 levels.
RGB
For dual color or RGB+CCT(WW/CW), adjust color temperature by WW/CW channel,
short
press
11
levels, long press 2s get max or min color temperature
.
For RGB, adjust color temperature by mix R/G/B channel,11 levels.
For RGBW, adjust color temperature by adjust W channel brightness,11 levels.
long press 2s get 100% or 0% White channel brightness.
Single color
W W W W W
Zone 2
DMX address
Zone 3
DMX address
Zone 4
DMX address
Zone 1
DMX address
Light Type
Light color channel
Dual color
RGB
RGBW
RGB+CCT
WW CW WW CW 0
R G B 0 0
R G B W W
1-5
6-10
11 -15
16 - 20
R G B WW CW
1-5
6-10
11 -15
16 - 20
1-5
6-10
11 -15
16 - 20
1-5
6-10
11 -15
16 - 20
1-5
6-10
11 -15
16 - 20
Touch Panel work as DMX512 Master
After connect with DMX decoders, please set the DMX decoders address as below:
User Manual Ver 2.0.2
Page 2
T15
Wall Mounted Touch Panel
Dynamic mode list
No.
Name
No.
RGB jump
RGB smooth
6 color jump
6 color smooth
Color temperature smooth
1
2
3
4
5
6
7
8
9
10
Name
RGB fade in and out
Red fade in and out
Green fade in and out
Blue fade in and out
White fade in and out
Wiring Diagram
AC100-240V
L
N
INPUT
100-240VAC
GND
D+
D-
DMX OUTPUT
D+
D-
DMX
signal
AC100-240V
L
N
INPUT
100-240VAC
GND
D+
D-
DMX OUTPUT
D+
D-
