background image

DOL 38-2 Frequency Converter

Technical User Guide

15

4.3 LED indication on the motor controller/frequency converter

The motor controller/frequency converter is equipped
with a two-color LED for indication of different operating
modes.

LED is located on the underside next to the cable
glands.

• Constantly green when mains voltage is connected.
• Constantly red in case of at least one critical alarm.
• Flashes red in case of at least one non-critical alarm.

4.4 Alarms

The motor controller/frequency converter including relay module provides alarm monitoring which monitors the
optimal and flawless operation and generates an alarm if operating or performance problems are observed.

Alarms are divided into "critical" alarms and "non-critical" alarms.

“Critical" alarms stop the motor controller/frequency converter/motor, LED emits red light and the alarm relay is
activated.

“Non-critical" alarms reduce the performance of the motor controller/frequency converter/motor, and the LED
flashes red.

The built-in alarm monitoring stops the motor controller/frequency converter/motor.

The alarm automatically resets, if the error ceases, and motor controller/frequency converter/motor starts.

Reset the alarm, if the maximum number of restarts (5 x/60 min) is exceeded.

Disconnect the mains voltage for more than 60 sec and the alarm will automatically be reset.

Alarm overview

Error

Alarm priority

Motor controller/frequency

converter/motor

Error

Alarm priority

Supply voltage too high

Critical

Stopped after 5 restart at-

tempts caused by the same

error within 60 minutes

Emits red

light

Enabled

Current consumption of the mo-
tor too high

Phase errors; one or more
phases interrupted (L1, L2, L3)

Obstructed impeller

Wrong direction of rotation

Phase error on the motor supply
(U, V, W)

Internal communication error

Supply voltage too low

Non-critical

Reduced performance

Flashes red

Not activated

Internal temperature of motor
controller too high.

(>95 °C)

Motor current has reached its
limit value

Error in internal EEPROM circuit

Ripple voltage too high

Summary of Contents for 110451

































Reviews: