Skoda Rapid NH 2014 Page 247 Workshop Manual Download

Page: 247 / 319

WARNING

Switch on the ignition before connecting the battery. Improper

handling of pyrotechnic components may lead to unwanted

deployment after the battery has been connected. Nobody

should be inside the vehicle when the battery is being connec‐

ted.

– Work procedure for connecting the battery ⇒ Electrical sys‐

tem; Rep. gr. 27 ; Disconnecting and re-connecting the bat‐

tery .

Note

If the airbag control indicator - K75 - indicates a fault after as‐

sembly, the event memory must be queried ⇒ Vehicle diagnostic

tester.

3.17

Head airbag

3.17.1

Summary of components - head airbag

1 - Anti-twist protection line

❑ Used to protect against

twisting during installa‐

tion.

❑ It must be visible over

the entire length of the

airbag in the installed

condition.

2 - Head airbag

❑ On the driver's and front

passenger's side with

airbag igniter.

WARNING

Observe the safety in‐

structions for pyrotech‐

nic

components

⇒ “3.3 Observe the gen‐

eral safety instructions

for working on airbag,

belt tensioner and bat‐

tery separation units (py‐

rotechnical

compo‐

nents)”, page 225

❑ Removing and installing

⇒ “3.17.2 Removing and

installing head airbag

with ignition for head air‐

bag driver's side/front

passenger side N251 /

N252 ”, page 240

3 - Screw

❑ Always use a new screw

after disassembly.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

3. Airbag

239

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands

Skoda Rapid NH 2014, Workshop Manual

Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands