Skoda Rapid NH 2014 Workshop Manual Download

Page: 231 / 319

2.2

Special instructions for the belt tension‐

WARNING

♦ The open end of a belt tensioner must never be pointed

towards people.

♦ Handle the seat belt tensioner units with great care when

removing and installing. A high risk and injury potential

exists through rough improper handling of seat belt ten‐

sioner units.

♦ When connecting the seat belt tensioner units, all me‐

chanical parts including the parts of the three point seat

belt, must be correctly secured. If it is not possible to con‐

nect the seat belt tensioner unit because there is not

enough space, the seal belt must be fully rolled up before

connecting. In this case, there is no increased safety risk

if further safety measures are observed and respected.

These include mainly disconnecting the battery and the

electrostatic discharge of the mechanic before connecting

the seat belt tensioner unit.

♦ Depending on the accident, it may be possible that the belt

tensioner was ignited, the belt force limiter, however, was

NOT ignited. These components are handled in the same

way as non-ignited components!

2.3

Storage, transport and disposal of air‐

bag, belt tensioner and battery separa‐

tion units (pyrotechnical components)

WARNING

♦ The storage is subject to the respective national legisla‐

tion.

♦ The transport is subject to national and international leg‐

islation, in which packaging, marking, labeling, and ac‐

companying documents are regulated in detail.

♦ Non-ignited pyrotechnical components must be discarded

in the original packaging in compliance with the applicable

disposal procedure according to the national legislation!

In case you have any questions, please contact your im‐

porter.

♦ Only fully ignited pyrotechnical components may be dis‐

posed of as industrial waste.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

2. Inspect seat belts

223

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands

Skoda Rapid NH 2014, Workshop Manual

Search results

Summary of Contents for Rapid NH 2014

Reviews:

Related manuals for Rapid NH 2014

Brands by name

Popular brands