manualshive.com logo in svg

Skoda Rapid NH 2014, Workshop Manual

Share
Download
Skoda Rapid NH 2014 Workshop Manual Download Page 146

4 - Nut

❑ Tightening torque - 20 Nm.

5 - Impact absorber (depending upon vehicle equipment)

❑ Secured with double-sided adhesive tape.

6 - Nut

❑ Tightening torque - 2.2 Nm.

7 - Guide section
Removing

– Remove the rear bumper 

⇒ “2.1.2 Remove the rear bumper”, page 136

 .

– Release the nuts 

⇒ Item 6 (page 138)

 .

– Remove the guide section from the vehicle.

Installing

– The installation occurs in reverse order.

8 - Screw

❑ Tightening torque - 2.2 Nm.

9 - Lateral guide section
Removing

– Remove the rear bumper 

⇒ “2.1.2 Remove the rear bumper”, page 136

 .

– Release screws 

⇒ Item 8 (page 138)

 .

– Remove the guide section from the vehicle.

Installing

– The installation occurs in reverse order.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

138

     Rep. gr.63 - Bumpers

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands