SKLADOVA TEHNIKA Metalurgia Instruction Manual Download Page 7

 

The surface of the cooker can be:  

 

With enamel finish. They can be washed with standard commercial cleaning materials, 
which are acid free and you can polish them with a soft towel. 

 

Painted  with  epoxy-polyester  powder.  They  have  to  be  cleaned  by  the  same  way  like 
the enameled parts. In order to preserve the surface from damage this can be done only 
when the cooker is cold,  

 

Painted with heat-resistant paint. This surface can be cleaned with dry and soft brush. 
The paint will reach its final resistance after a few hours of heating, that’s why you have 
to avoid touching the outer surface or you can damage the paint. During heating, the 
paint will release specific smell as a result of paint baking. The smell will disappear after 
a few hours. You will need to ensure fresh air in the room. 

Attention! 

When cleaning do not use sharp objects and abrasive materials! 

After  using  the  oven  it  has  to  be  cleaned  when  it  is  still  warm  and  then  to  be  dried.  When 
needed,  the  glass  of  the  oven  can  be  cleaned  only  when  it’s  cold,  by  washing  it  with  soap 
solution. When the cooker is operating you have to avoid splashing water on it. 

The glasses is 

not covered by the warranty! 

The manufacturer keeps the right to make changes in  design and construction 

without violating the technical and operational quality of the fireplace. 

 

6. Important directions for fire-precaution and safety regulations. 

Please observe the following requirements for fire-precaution and safety regulations. 
The door of the combustion chamber should always be firmly closed even when the fireplace is 

not  working.  It  should  be  serviced  only  by  some  operating  tools  or  heat-resistant  glove,  which  is 
placed inside the cooker. 

The cooker should be installed only on a non-combustible floor. Under the oven door there is 

a niche with door (for Plamak and Plamak B) and niche (for Metalurgia). They are decorative and 
storing easy inflammable materials in them is not allowed. 

 

The  fireplace  and  the  flue  draught  pipes  should  be  at  least  80cm  away  from  combustible 
objects or constructions. 

 

Installation,  repairs  and  adjustment  of  the  water  heating  system  should  be  done  only  by 
authorized organizations. 

 

Using easily inflammable liquids is not allowed at ignition. 

 

Vertical  connection  of  flue  draught  pipes  with  the  chimney  through  floor  structures  is  not 
allowed. 

 

The  presence  of  easily  inflammable  and  explosive  substances  in  the  heated  room  is  not 
allowed. 

 

The ash disposal and cleaning of the cooker should be done only at safe places  and when 
the fireplace has cooled down. 

 

The cooker is designed for local heating of rooms with normal fire danger. 

 

It  is  prohibited  to  put  combustible  materials  and  objects  on  the  fireplace  or  in  immediate 
proximity of it. 

 

 

The  cooker  is  not  designed  to  be  used  by  children  and  persons  with  limited  physical, 
sensuous  and  mental  abilities,  or  by  people  with  not  enough  experience  and  knowledge, 
except in cases when they are watched and instructed how to work with this type of heater, 
by someone who is responsible for their own safety. 

Incineration danger!

 

We recommend the following instructions when there is a fire in the chimney: 

 

Close the combustion air regulator! 

 

Call the fire brigade in your neighborhood! 

 

Don’t try to extinguish the fire with water by yourself! 

Summary of Contents for Metalurgia











Reviews: