background image

20

•  Checking/adjusting of 90° fence alignment 

!  disconnect the plug

-  rotate the saw table to the 0° position and lock in place

-  lower the tool arm and lock in place

-  check for a 90° angle between blade and fence L with 

a square (ensure the square contacts the saw blade 

body and not its teeth)

-  if necessary, adjust the 90° fence alignment as follows:

1) loosen 4 hex screws L1

2) adjust fence until blade and fence have full contact 

with the square

3) tighten 4 hex screws L1

•  Cable storage 

§

APPLICATION ADVICE

•  Special workpieces

-  ensure that curved or round workpieces are especially 

secured against slipping

-  at the cutting line no gap may exist between the 

workpiece and the fence or saw table

-  if necessary, fabricate a special fixture

•  For working with floor mouldings illustration 

 can be 

used as reference

•  Always face the good side of the workpiece down to 

ensure minimum splintering

•  Only use sharp saw blades of the correct type

-  quality of cut improves by the number of teeth

-  carbide tipped blades stay sharp up to 30 times longer 

than ordinary blades

MAINTENANCE / SERVICE

•  Always keep tool and cord clean (especially the 

ventilation slots at the back-end of the motor housing)

!  disconnect the plug before cleaning

•  Clean saw blade immediately after use (especially from 

resin and glue)

!  the saw blade becomes very hot during use;  

do not touch it before it has cooled down

•  If the tool should fail despite the care taken in 

manufacturing and testing procedures, repair should be 

carried out by an after-sales service centre for SKIL 

power tools

-  send the tool 

undismantled

 together with proof of 

purchase to your dealer or the nearest SKIL service 

station (addresses as well as the service diagram of 

the tool are listed on www.skilmasters.com)

ENVIRONMENT

• 

Do not dispose of electric tools, accessories and 

packaging together with household waste material

 

(only for EU countries)

-  in observance of European Directive 2002/96/EC on 

waste of electric and electronic equipment and its 

implementation in accordance with national law, 

electric tools that have reached the end of their life 

must be collected separately and returned to an 

environmentally compatible recycling facility

-  symbol 

 will remind you of this when the need for 

disposing occurs

 DECLARATION OF CONFORMITY

•  We declare under our sole responsibility that this product 

is in conformity with the following standards or 

standardized documents: EN 61029, EN 61000, 

EN 55014, in accordance with the provisions of the 

directives 2006/95/EC, 2004/108/EC, 2006/42/EC

• 

Technical file at

: SKIL Europe BV (PT-SEU/PJE), 

4825 BD Breda, NL

Arno van der Kloot

Vice President

Operations & Engineering

SKIL Europe BV, 4825 BD Breda, NL

Jan Trommelen

Approval Manager

  01.11.2010

NOISE/VIBRATION

•  Measured in accordance with EN 61029 the sound 

pressure level of this tool is 93 dB(A) and the sound 

power level 106 dB(A) (standard deviation: 3 dB), 

 

and the vibration < 2.5 m/s² (hand-arm method; 

uncertainty K = 1.5 m/s²)

•  The vibration emission level has been measured in 

accordance with a standardised test given in EN 61029; 

 

it may be used to compare one tool with another and as 

 

a preliminary assessment of exposure to vibration when 

using the tool for the applications mentioned

-  using the tool for different applications, or with different 

or poorly maintainted accessories, may significantly 

increase

 the exposure level

-  the times when the tool is switched off or when it is 

running but not actually doing the job, may significantly 

reduce

 the exposure level

!  protect yourself against the effects of vibration by 

maintaining the tool and its accessories, keeping 

your hands warm, and organizing your work patterns

Scie à onglets radiale 

3855

INTRODUCTION

•  Cet outil est une machine fixe, conçue pour effectuer dans 

le bois des coupes droites longitudinales et transversales 

ainsi que des angles d’onglet (il est possible de réaliser 

des angles d’onglet horizontaux de -47° à +47° et des 

angles de biseau verticaux de 0° to 45°)

•  Lisez et conservez ce manuel d’instruction 

2

•  La séquence des numéros apparaissant sur la fiche 

d’instructions d’assemblage 

séparée

 correspond à la 

séquence des étapes à suivre pour le montage de l’outil

• 

Utilisez uniquement l’outil lorsqu’il est tout à fait 

assemblé correctement

 (veuillez noter que Skil ne peut 

être tenue responsable de dégâts à l’outil et/ou de blessures 

personnelles résultant du montage incorrect de l’outil)

•  Avant d’utiliser cet outil pour la première fois, collez 

l’autocollant fourni dans votre langue sur le texte anglais 

de l’étiquette d’avertissement A 

5

Summary of Contents for Masters 3855





















Reviews: