background image

10

•  Dust from material such as paint containing lead, some 

wood species, minerals and metal may be harmful 
(contact with or inhalation of the dust may cause 
allergic reactions and/or respiratory diseases to the 
operator or bystanders); 

wear a dust mask 

5

 and 

work with a dust extraction device when 
connectable

•  Certain kinds of dust are classifi ed as carcinogenic 

(such as oak and beech dust) especially in conjunction 
with additives for wood conditioning; 

wear a dust 

mask 

5

 and work with a dust extraction device 

when connectable

•  Follow the dust-related national requirements for the 

materials you want to work with

•  Avoid damage that can be caused by screws, nails and 

other elements in your workpiece; remove them before 
you start working

• 

Use suitable detectors to find hidden utility lines or 
call the local utility company for assistance

 (contact 

with electric lines can lead to fi re or electrical shock; 
damaging a gas line can result in an explosion; 
penetrating a water pipe will cause property damage or 
an electrical shock)

•  Ensure that the collet size corresponds with the shaft 

size of the accessory

DURING USE

•  If the cord is damaged or cut through while working, do 

not touch the cord, but immediately disconnect the plug

•  Never use the tool when cord is damaged; have it 

replaced by a qualifi ed person

•  Keep hands away from rotating accessories
• 

Never use spindle lock while tool is running

 

(damage due to improper handling will be excluded 
from the guarantee)

•  In case of electrical or mechanical malfunction, 

immediately switch off the tool and disconnect the plug

AFTER USE

•  After switching off the tool, never stop the rotation of 

the accessory by a force applied against it

•  Store tool in locations where temperature will not 

exceed 50°C

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
•  Do not connect the blue (= neutral) or brown (= live) wire 

in the cord of this tool to the earth terminal of the plug

•  If for any reason the old plug is cut off the cord of this 

tool, it must be disposed of safely and not left 
unattended

USE

• Mounting of accessories 

6

!  switch off the tool and disconnect the plug
!  ensure that collet size corresponds with shaft 

size of accessory

-  push spindle-lock button A and hold it while you turn 

collet nut B by hand until the spindle lock prevents 
further rotation and loosen collet nut B with wrench C

!  push spindle-lock button A only when tool is at a 

standstill

-  insert required accessory in collet D (leave 

approximately 3 mm of the shaft exposed)

-  push spindle-lock button A and hold it while you 

tighten collet nut B with wrench C

!  avoid excessive tightening of collet nut B
!  never tighten collet nut, if there is no accessory in 

collet; collet may be damaged

•  Before using the tool

-  ensure that accessory is correctly mounted and fi rmly 

tightened

-  check if accessory runs freely by turning it by hand
-  test-run tool for at least 30 seconds at highest no-

load speed in a safe position

-  stop immediately in case of considerable vibration or 

other defects and check tool to determine the cause

• On/off

-  switch on/off the tool by pushing switch E 

2

 in 

“I”/”O” position

!  be aware of the sudden impact when the tool is 

switched on

• Speed control 

7

 

For optimal results on different materials
-  select speed with wheel F (also while tool is running)
- use 

table 

8

 as reference for determining the right 

speed

-  before starting a job, fi nd the optimal speed by 

testing out on spare material

!  after longer periods of working at low speed, 

allow the tool to cool down by running it for 
approximately 3 minutes at high speed with no 
load

• Depth adjustment accessory 

9

 

For guiding the tool along the workpiece at a pre-set 
cutting depth
-  release lever G before mounting/removing 

accessory H onto/from tool collar

!  lock lever G after mounting accessory H

-  loosen adjustment screw K counter-clockwise with 

wrench C as illustrated

-  slide depth gauge L up or down to the desired 

cutting depth and tighten screw K clockwise

•  Dust suction accessory 

0

 

For combining tool guidance at a pre-set cutting depth 
with dust suction
-  release lever G before mounting/removing 

accessory M onto/from tool collar

!  lock lever G after mounting accessory M

-  loosen 2 adjustment knobs N counter-clockwise
-  slide depth gauge L up or down to the desired 

cutting depth and tighten 2 adjustment knobs N 
clockwise

-  connect vacuum cleaner to extension P

!  never let the vacuum cleaner hose interfere with 

the cutting operation

• Operating the tool 

!

-  insert multi-functional bit Q
-  mount depth adjustment accessory H or dust suction 

accessory M

-  set wheel F 

2

 to desired speed

-  place the bit onto the workpiece at a 45° angle
-  switch on the tool
-  slowly lower the bit into the workpiece at a 45° angle
-  after reaching the desired cutting depth, move the 

tool to its normal working position again

Reviews: