background image

Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool

Never use the tool without the original protection guard
system

This tool should not be used by people under the age of
16 years

The noise level when working can exceed 85 dB(A);
wear ear protection 

If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug

Never use tool when cord is damaged; have it replaced
by a qualified person 

Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)

This tool is not suitable for wet cutting

After switching off your circular saw, never stop the
rotation of the saw blade by a lateral force applied
against it

Never use circular saw blades made of high speed steel
(HSS)

Never use grinding/cutting discs with this tool

Do not cut material containing asbestos

Wear a dust protection mask when working with
materials which produce dust that is detrimental to
health; inform yourself beforehand about the materials to
be worked on

Do not attempt to cut extremely small workpieces

Remove all obstacles on top of as well as underneath
the cutting path before you start cutting

Do not work overhead with the tool

Only use a saw table provided with a switch that
prevents restarting of the motor after interruption of
voltage

Only use a saw table provided with a kerf guide

Always disconnect plug from power source before
making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug

If for any reason the old plug is cut off the cord of this
tool, it must be disposed of safely and not left unattended

USE

Changing saw blade 

3

- take hex key A from storage B
- push spindle-lock button C and hold it while you

remove blade bolt D with hex key

! push spindle-lock button C only when tool is at a

standstill

- release spindle-lock button C
- remove flange E
- open lower guard F by using lever G and hold it while

you change saw blade with saw teeth and arrow
printed on saw blade pointing in same direction as
arrow on lower guard

- release lower guard F
- mount flange E

! make sure that clamping surfaces H of flanges are

perfectly clean and face the blade

- push spindle-lock button C and hold it while you

tighten blade bolt with hex key 1/8 turn past finger
tight (ensures slippage of saw blade when it
encounters excessive resistance thus reducing motor
overload and saw kickback)

- release spindle-lock button C

Adjusting cutting depth (0-55 mm) 

4

- for an optimal quality cut the saw blade should not

extend more than 3 mm below the workpiece

- loosen lever J
- raise/lower foot K until desired cutting depth is set on

scale using indicator L

- tighten lever J

Adjusting cutting angle (0-45°) 

5

- loosen knob M
- tilt tool until desired cutting angle is set on scale using

indicator N

- tighten knob M 

! when bevel cutting, cutting depth does not

correspond with value on cutting depth scale

90° Cutting angle check 

5

- adjust and tighten foot K to maximum cutting depth 

4

- adjust and tighten cutting angle to 0°
- check for 90° angle between the blade and bottom of

foot with a square

Adjustable saw line visor P 

6

a

- for guiding tool along desired line of cut marked on the

workpiece

- for a straight 0° cut or a 45° bevel cut use the indicator

line concerned

! the wide part of the foot should rest on the

supported part of the workpiece

- can be adjusted to allow you to choose whether waste

material is on inner or outer side of blade 

6

b

! cutting width is determined by width of blade

teeth and not by width of blade body

! always make trial cuts first to verify actual line of

cut

Dust suction
- connect vacuum cleaner to extension Q 

2

! never let the vacuum cleaner hose interfere with

the lower guard or the cutting operation

- one may also use a dust bag (SKIL accessory

2610387402)

Operating the tool 

2

- connect plug with power source
- always hold handle R firmly with one hand and handle

S firmly with the other hand

- place tool with front end of foot flat on workpiece

! ensure that the saw teeth are not engaged into the

workpiece

- switch on tool by first pressing knob T (= safety switch

which cannot be locked) and then pulling trigger V 

! the tool should run at full speed before the blade

enters into the workpiece

- lower guard F opens automatically when saw blade

enters the workpiece (open lower guard manually by
using lever G only for special cuts such as plunge
cuts)

10

Summary of Contents for 5855

















Reviews: