SKF PowerLuber 1882E User And Maintenance Instructions Download Page 10

Charger

 

•  Before using a battery charger, read all  

instructions and cautionary markings on 
battery charger, battery pack, and product 
using battery  

•  Do not expose charger to rain, snow or 

frost  

•  Do not abuse cord  Never carry charger by 

cord or pull on it to disconnect from  
receptacle  Pull by plug rather than cord 
when disconnecting charger  Have 
damaged or worn power cord and strain  
reliever replaced immediately  Do not  
attempt to repair power cord  

•  Locate cord so that it will not be stepped 

on, tripped over, or otherwise subjected to 
damage or stress  

•  Do not use an extension cord unless  

absolutely necessary  Use of improper  
extension cord could result in a risk of fire 
and electric shock  

•  Do not operate charger with damaged 

cord or plug  Replace immediately, to avoid 
a hazard  Do not attempt to repair  
power cord  

•  Do not operate charger if it has received a 

sharp blow, been dropped, or otherwise 
damaged in any way, take it to a qualified 
service center  

•  Do not disassemble charger or battery 

pack  Take it to a qualified service center 
when service or repair is required   
Incorrect reassembly may result in risk of 
electrical shock or fire  

•  Unplug charger from outlet before  

attempting any cleaning to reduce risk of 
electric shock  

•  Charge the battery pack in a well 

ventilated place; do not cover the charger 
and battery with anything while charging  

•  Do not store the charger or battery packs 

in locations where the temperature may 
reach or exceed 50 °C 

(122 °F)

 such as a 

metal tool shed, or a car in the summer 
which can lead to deterioration of the 
battery  

•  Do not charge battery pack when the 

temperature is below 5 °C 

(40 °F)

 or above 

40 °C 

(105 °F)

  This is very important for 

proper operation  

•  Do not incinerate battery pack  It can  

explode in a fire  

•  Do not charge battery in damp or wet 

locations  

•  Do not attempt to charge any other 

cordless tool or battery pack with Lincoln 
model 1870 series charger 

 



DANGER*

Do not charge SKF model 1871 battery packs 
with any other charger  

To reduce risk of injury, Lincoln model 

1870 or 1870E chargers should only be used 
to charge Lincoln battery pack model 1871  
Other types of batteries may burst 

Failure to comply will result in serious per-

sonal injury or death  

NOTE

Charger is intended for indoor use only 

NOTE

Read instruction manual before use 

NOTE

Do not attempt to replace charger unit with 
regular main plug  Charger is double 
insulated and no ground wire is required  
Check mains voltage corresponds to voltage 
on rating plate  

*

  Indicates change 

•  Do not short across the terminals of the 

battery pack  Extremely high temperatures 
could cause personal injury or fire  

•  This appliance is not intended for use by 

persons (including children) with reduced 
physical, sensory or mental capabilities  
Do not use this appliance if not 
experienced or have knowledge of how  
it operates  

•  Dispose of expended batteries properly  

The SKF TLGB 20-2 battery pack contains 
rechargeable, lithium-ion batteries  These 
batteries must be recycled or  
disposed of properly  Drop off expended 
battery packs at your local replacement 
battery retailer, or your recycling center  *

10

Summary of Contents for PowerLuber 1882E

























Reviews: