manualshive.com logo in svg

SKC 224-PCXR8, Operating Instructions Manual

Share
Download
SKC 224-PCXR8 Operating Instructions Manual Download Page 23

21

Installing the Battery Pack

To enhance battery life, SKC ships battery packs separate from the pump. 
Once installed, completely charge battery pack before operating pump.

1.  Loosen the two case screws above and below the belt clip.
2.  Slip the front edge of the battery pack under the belt clip and 

position battery pack to engage the grooves in the case.

3.  Slide battery pack toward the pump until it is 

fl

 ush with the 

pump case on all sides.

4.  Install two battery screws and tighten the case screws loosened 

in Step 1.

5.  Charge battery completely. For optimum charge, ensure pump 

is not running during charging.

Replacing the Battery Pack

To enhance battery life, SKC ships battery packs separate from the pump. 
Once installed, completely charge battery pack before operating pump.

For information on SKC pump batteries, visit www.skcinc.com/
instructions/1756.pdf.

1.  Remove the two screws that secure the battery pack and 

loosen the two case screws above and below the belt clip.

2.  Carefully slide battery pack out from under the belt clip. En-

sure that the battery is kept level.

3.  Slip the front edge of the new battery pack under the belt clip 

and position battery pack to engage the grooves in the case.

4.  Slide the battery pack toward the pump until it is 

fl

 ush with the 

pump case on all sides.

5.  Reinstall battery screws and tighten the case screws.

Back of pump 

with battery 

pack sliding out

Beltclip

Case screw 
(not shown)

Ba

tt

 ery pack screws

Case screw 

Case grooves

Ba

tt

 ery connector

Important Cautions/Warnings on next page

Summary of Contents for 224-PCXR8































Reviews:

No comments

Brands by name

Popular brands

Load more brands