SKC 224-44XRM Operating Instructions Manual Download Page 18

17

SKC INC.

LIMITED ONE YEAR WARRANTY

1. 

SKC warrants that its instruments provided for industrial hygiene, environmental, gas analysis, 

and safety and health applications are free from defects in workmanship and materials under normal 
and proper use in accordance with operating instructions provided with said instruments. The term 
of this warranty begins on the date the instrument is delivered to the buyer and continues for a 
period of one (1) year.

 
 

This warranty does not cover claims due to abuse, misuse, neglect, alteration, accident, or use in 

application for which the instrument was neither designed nor approved by SKC Inc. This warranty 
does not cover the buyer’s failure to provide for normal maintenance, or improper selection or 
misapplication. This warranty shall further be void if changes or adjustments to the instrument are 
made by other than an employee of the seller, or if the operating instructions furnished at the time of 
installation are not complied with.

2. 

SKC Inc. hereby disclaims all warranties either expressed or implied, including any implied 

warranties of merchantability or 

fi

 tness for a particular purpose, and neither assumes nor authorizes 

any other person to assume for it any liability in connection with the sale of these instruments. No 
description of the goods being sold has been made a part of the basis of the bargain or has created or 
amounted to an express warranty that the goods will conform to any such description. Buyer shall 
not be entitled to recover from SKC Inc. any consequential damages, damages to property, damages 
for loss of use, loss of time, loss of pro

fi

 ts, loss of income, or other incidental damages. Nor shall 

buyer be entitled to recover from SKC Inc. any consequential damages resulting from defect of the 
instrument including, but not limited to, any recovery under section 402A of the Restatement, Second 
of Torts.

3. 

This warranty extends only to the original purchaser of the warranted instrument during the 

term of the warranty. The buyer may be required to present proof of purchase in the form of a paid 
receipt for the instrument.

4. 

This warranty covers the instrument purchased and each of its component parts.

5. 

In the event of a defect, malfunction, or other failure of the instrument not caused by any 

misuse or damage to the instrument while in possession of the buyer, SKC Inc. will remedy the 
failure or defect without charge to the buyer. The remedy will consist of service or replacement of the 
instrument. SKC Inc. may elect refund of the purchase price if unable to provide replacement and 
repair is not commercially practicable. 

6.  

(a) To obtain performance of any obligation under this warranty, the buyer shall return the 

instrument, freight prepaid, to SKC Inc., at the following address:

 

 

 

 

 

 

SKC Inc., National Service Center

   863 

Valley 

View 

Road

 

 

 

Eighty Four, PA 15330 USA

 
 

(b) To obtain return authorization information or for further information on the warranty 

performance you may telephone 724-941-9701 at the above address. 

See Service Policy section in 

operating manual (if applicable).

7. 

This warranty shall be construed under the laws of the Commonwealth of Pennsylvania which 

shall be deemed to be the situs of the contract for purchase of SKC Inc. instruments.

8. 

No other warranty is given by SKC Inc. in conjunction with this sale.

Form #3755 Rev 0207

Summary of Contents for 224-44XRM




















Reviews: