manualshive.com logo in svg

Sitecom WLM-3500, User Manual

Share
Download
Sitecom WLM-3500 User Manual Download Page 15

 

 

LAN settings 

The LAN tab gives you the opportunity to change the IP settings of the WLM-

3500. 

 

Click 

<Apply>

 at the bottom of this screen to save any changes.  

 

 

IP  address

  192.168.0.1.  It  is  the  router’s  LAN  IP  address  (Your  LAN  clients 

default gateway IP address). 

 

IP  Subnet  Mask

  255.255.255.0  Specify  a  Subnet  Mask  for  your  LAN 

segment. 

 

DHCP Server

 Enabled by default. You can enable or disable the DHCP server. 

When DHCP is disabled no ip-addresses are assigned to clients and you have 

to use static ip-addresses. When DHCP server is enabled your computers will 

be assigned an ip-address automatically until the lease time expires. 

 

Lease  Time

  Forever.  In  the  Lease  Time  setting  you  can  specify  the  time 

period that the DHCP lends an IP address to  your LAN clients. The  DHCP will 

change  your  LAN  client’s  IP  address  when  this  time  threshold  period  is 

reached. 

Summary of Contents for WLM-3500





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands