manualshive.com logo in svg

Sitecom WL-308, User Manual, Page: 64 / 73

Share
Download
Sitecom WL-308 User Manual Download Page 64

WL-308 Gaming Router 

 

 

 

 

 

 

 

         Full Manual 

 

 

 64 

 

This option allows you to restore a backup configuration from a file to the device. 
Click  on  the 

Browse

  button  to  select  the  file  and  then  click  on 

Restore 

Configuration from a File

 button. 

 
The system then prompts you to reboot the device.  
 

 

 
Click on the 

OK

 button to continue.  You will then see the 

Rebooting

 page.  

 

 
 

Please wait while the system is rebooting.  

 
Note

: Do no un-plug the device during this process as this may cause permanent 

damage.  

 

Restore To Factory Default 

 

Click  on  the 

Restore  all  Settings  to  Factory  Defaults

  button.  This  option 

restores  al  configuration  settings  back  to  the  settings  that  were  in  effect  at  the 
time when the device was shipped from the factory.  
 

 

 
Once the dialog box appears, click on the 

OK

 button to confirm the action.   

 
Note

: The current settings will be lost.  

 

Click on the 

OK

 button to continue.  You will then see the 

Rebooting

 page.  

 

 

Summary of Contents for WL-308










































































Reviews:

No comments