sisel ENDA ERFA1 Series, Quick Start Manual

Page: 1 / 4

ENVIRONMENTAL CONDITIONS
- 25... +60 °C / -30... +100 °C (Shouldn't be icing and condensation in ambient.)
50% Relative humidity for +40°C temperature increases up to 90% at +20°C. (Shouldn't be condensation)
2
II
Max. 1000m
IP20 According to EN60529
Ambient/storage temperature
Relative humidity
Pollution degree
Overvoltage category
Altitude
Protection
Do not use the device in locations subject to corrosive and flammable gases.
OUTPUT
INPUT
ERFA1-240
40
180 - 280
150
400
1,6
5
880
50 - 60
> 0,75
160
Order code
Load Current, AC51/25ºC (Arms)
Load voltage (Vrms)
Overload current t=1s/25°C (Arms)
Non rep.surge current/25°C (Arms)
On-state voltage drop (Vrms)
Leakage current (mArms)
I²t for fusing t=10ms (A²s)
Frequency (Hz)
Power factor (CosΦ)
Minimum operating current (mArms)
Input signal
Transmission signal
Drop-out signal
Turn-on time
Dynamic input impedance
Protection
ENDA ERFA1 SERIES FAN SPEED CONTROLLER
ERFA1-240- EN-01-170420
SİSEL MÜHENDİSLİK ELEKTRONİK SAN. VE TİC. A.Ş.
Şerifali Mah. Y.Dudullu 34775
ÜMRANİYE/İSTANBUL
Tel : +90 216 499 46 64 Pbx. Fax : +90 216 365 74 01
url : www.enda.com.tr
Barbaros Cad. No:18
1/4
ENDA TM
ORDER CODE :
ERF A 1 2 40 - F -
Product Base Code
Fan Speed Control
Load Current
40A AC
Load Voltage
AC
Number of Pole
Single Pole
Load Voltage
180-280V AC
ERF
A
1
40
2
Fan
Fan F
0/4-20mA, 0/1-5V DC, 0/2-10V DC or ~ 10k potentiometer.
0,2mA (for mA input), 0,08V (for V input)
0,18mA (for mA input), 0,075V (for V input)
15ms
100Ω (for mA input), 10k (for V input)
1k (Device may be damaged at ±12V DC and above voltages) Ω Ω
Ω
Please read this document carefully before using this product. The guarantee will be invalidated if the device is damaged by not
following instructions detailed in the manual. The company shall not be responsible for any damage or losses however caused, which
may be experienced as a result of the installation or use of this product.
Thank you for choosing ENDA ERFA1 Series fan speed controller devices.
Protection feature for reverse connection is available.
While cleaning the device, solvents (thinner, gasoline , acid etc.) or corrosive materials must not be used.
Dimensions
Weight
GENERAL
Order code
Power supply
Isolation Voltage
Connection
Terminal screw torque
Product standard
Mo unting
Enclosure material
Fan (Optional)
40A AC Load current
280V AC Load voltage
CE Marked according to European Norms
0/4-20mA, 0/1-5V DC, 0/2-10V DC or 1kΩ ~ 10kΩ Potentiometer input
24V DC Sensor supply
4 Digits LED display
Phase angel or zero-cross controlled
Soft Start or Kick Start feature
Varistor protection for peak voltages
Sensor supply
ERFA 1-240
90-250 V AC , 50/60 Hz . 7 VA Max.
24V DC, 30mA
W46 x H110 x D117mm
Approx. 450g (boxed)
2500 Vrms between I/O terminals for 1 min.
For power line 16mm² cable (with 25mm² cable terminal) cable, for signal line can be connected 4mm² cable.
Max. 1,2Nm
EN 60947-4-3
Fan is controlled with thermostat and works at temperatures over 50°C.
Rail mount (EN60715,TH35)
Self extinguishing plastics (According to EN 60695-11-10 V-O)