TERMS
4 digits 7 segment red LED display
( 2 ),( 3 ),( 4 ),( 5 ) Tuþ takýmý
( 1 ) Digital display
Panel cut-out
Connection
cables
Depth
97mm
75mm
8
4
m
m
DIMENSIONS
68 mm
+0.7
6
8
m
m
+
0
.7
Rubber packing
Flush mounting
clamp
Panel
7
2
m
m
7
8
m
m
1
2
2/3
EI741A-E-05
CONNECTION DIAGRAM
10
9
184-253V AC
50/60Hz 7VA
230V AC
Supply
Switch
Cable size: 1,5mm²
Fuse
F 100 mA
250V AC
Neutral
Line
SUPPLY :
NOTE :
Fuse should
be connected
1) Measurement value, measurement unit, the minimum or the maximum measured values are
displayed in the run mode.
Parameter name, parameter value or a user defined unit is displayed in the programming mode.
3) De
Used for making the minimum and the maximum measured values equal in the run mode.
crement or parameter selection key in the programming mode.
2) Increment or parameter selection key in the programming mode.
Used for displaying measurement unit or the max. measured value in the run mode.
4) Menu selection key in the programming mode.
Used for displaying the minimum measured value in the run mode.
5) Used for selecting run and programming modes,
displaying
measurement unit or
adjusting parameters,
making the minimum and the maximum measured values equal.
ENDA
PROGRAMMABLE INDICATOR
PRG
SHIFT
MIN.
MAX.
UNIT
RESET
D.P.
SET
EI 741A
14mm
Micro switch
Character height
ENDA
ENDA
ENDA
ENDA
ENDA
ENDA
EI741A INDICATOR
EI741A-24AC INDICATOR
EI741A-24DC INDICATOR
EI741A-ASXX INDICATOR
EI741A-24AC-ASXX
INDICATOR
EI741A-24DC-ASXX
INDICATOR
INDUSTRIAL ELECTRONICS
INDUSTRIAL ELECTRONICS
INDUSTRIAL ELECTRONICS
INDUSTRIAL ELECTRONICS
INDUSTRIAL ELECTRONICS
INDUSTRIAL ELECTRONICS
INPUT
INPUT
INPUT
INPUT
INPUT
INPUT
+
+
+
+
+
+
+
+
+
GND
GND
GND
GND
GND
GND
GND
GND
GND
5
5
5
6
6
6
7
7
7
7
7
7
8
8
8
8
8
8
9
9
9
9
9
9
10
10
10
10
10
10
SN: XXXXXXXXX
SN: XXXXXXXXX
SN: XXXXXXXXX
SN: XXXXXXXXX
SN: XXXXXXXXX
SN: XXXXXXXXX
230V AC +10% -20%
50/60Hz 7VA
24V AC ±10%
50/60Hz 7VA
24V DC ±10%
7VA
24V AC ±10%
50/60Hz 7VA
24V DC ±10%
7VA
230V AC +10% -20%
50/60Hz 7VA
AUXILIARY SUPPLY
OUT XXV XXmA
AUXILIARY SUPPLY
OUT XXV XXmA
AUXILIARY SUPPLY
OUT XXV XXmA
Note 1) While panel mounting, additional distance required for
connection cables should be considered.
2) Panel thickness should be maximum 10mm.
3) If there is no 90mm free space at back side of the device,
it would be difficult to remove it from the panel.
-
Push up the flush-mounting
clamp in direction
1
as
shown in the figure above.
-
Then, pull out the clamp in
direction
2.
For removing mounting clamps:
ENDA EC762 is intended for installation in control panels. Make sure that the device is used only for intended purpose.
During an installation, all of the cables that are connected to the device must be free of energy. The device
must be protected against inadmissible humidity, vibrations, severe soiling and make sure that the operation temperature is not exceeded. All
input and output lines that are not connected to the supply network must be laid out as shielded and twisted cables. These cables should not be
close to the power cables or components.
The shielding must be
grounded on the instrument side.
The installation and electrical connections must be carried on by a qualified staff and must be
according to the relevant locally applicable regulations.
1) Mains supply cords shall meet the requirements of IEC 60227 or IEC 60245.
2) In accordance with the safety regulations, the power supply switch shall bring the identification of the relevant instrument and it
should
be easily accessible by the operator.
Note :
Holding screw
0.4-0.5Nm
Equipment is protected throughout
by DOUBLE INSULATION.
ENDA
PROGRAMMABLE INDICATOR
PRG
SHIFT
MIN.
MAX.
UNIT
RESET
D.P.
SET
EI 741A