background image

UPA-61W

no signal being received. 

51.  MIC. ON & Diversity Signal Indicator 

These indicators light up during standby. When microphone signal is received, the A or B signal indicator lights up to indicate the 
reception of microphone. 

52. POWER ON Indicator 

When the unit powered on, this blue LED will lights up. It indicates the receiver is on. 

53. SQUELCH Control 

This control is SQ noisy controlled adjustment. The job of squelch circuit is to reduce audible noise. It eliminates noise during 
pause in the audio signal by muting the receiver. Before you turn on the receiver, please adjust SQ control until the jamming 
signal has disappeared. (Clockwise) 

54. VOLUME Control 

This knob sets the output audio signal level. Turn the knob fully clockwise for the maximum volume; and turn the knob fully 
counterclockwise for the minimum volume. 

55. TO CH1 & TO MAIN Switch  

From this switch you can choose the microphone signal sent to CH1 or to MAIN. Switching it to “TO CH1”position, the signal 
will come through CH1, after it is adjusted by the 3-band EQ and DSP/FX control, then sent to main channel, you can also 
adjust the signal by using the 7-band graphic EQ and the DSP processor, then sent to the MAIN OUT. Switching it to “TO MAIN” 
position, the signal will only go to the main channel, after adjusted by the 7-band graphic EQ and the DSP processor, then sent 
to MAIN OUT. 

56. MIC1 TO CH1/MIC2 TO CH2 & TO MAIN Switch  

From this switch you can choose the microphone signal 
sent to CH1/CH2 or to MAIN. Switching it to “MIC1 
TO CH1/MIC2 TO CH2”position, the signal will come 
through CH1/CH2, after it is adjusted by the 3-band 
EQ and DSP/FX control, then sent to main channel, you 
can also adjust the signal by using the 7-band graphic 
EQ and the DSP processor, then sent to the MAIN OUT. 
Switching it to “TO MAIN” position, the signal will only 
go to the main channel, after adjusted by the 7-band 
graphic EQ and the DSP processor, then sent to MAIN 
OUT. 

49

50

51

53

56

54

52

55

With one microphone

With two microphone

Summary of Contents for UPA-612W

















Reviews: