background image

一般安全事項說明

GENERAL  SAFETY 
INSTRUCTIONS

警告

當使用這台機器,基本安全預防應恆被遵守
,以減輕火災、電擊、或是個人傷害的風險

   

。包含以下注意事項。

    

在操作這台機器之前,請閱讀所有說明並且
緊記於心。

1. 

保持工作場所清潔

雜亂的環境與椅子會招引危害。

2. 

考量工作場所環境

勿暴露電源於雨水之中、勿在溼氣重的地方
或潮濕的場所使用機械器具。保持工作場所
良好整齊。當有引發火災或爆炸危險時,勿
使用電源工具。

 

3. 

免於電擊危害

避免身體接觸地線或是接地表面。

(

即:

管線,發熱物體,以及冷凍庫

)

4. 

勿使孩童接近

不要讓訪客接觸工具或是延伸管線。

5. 

適當的穿著

    

不要穿著寬鬆衣物或是穿戴珠寶,這可能被
活動零件拉扯而導致危險。穿戴護髮套可包
住長髮。

6. 

不要任意拉扯電線

絕不要用電源端拉扯機器,或是從插座猛拉
電線來拔掉電線。使電線遠離熱源、油類或
是尖銳邊緣。

     

7.

謹慎保養機器

遵從指示來添加潤滑油或是更換附件。定期
檢測工具用線,如果有所損害,請使用合格
的維修器具來修復。

Warning!

     When using this machine, basic safety 
     Precautions should always be followed to 
     reduce the risk of fire, electric shock and 
     personal injury, including the followings. 
     Read all these instructions before 
     operating this product and save these 
     instructions.

1.  Keep work area clean

     Cluttered areas and benches invite 
     injuries.

2.  Consider work area environment

     Do not expose power to rain. Do not use 
     machine tools in damp or wet locations.
     Keep work area well lit.
     Do not use power tools where there is risk 
     to cause any fire or explosion.

3.  Guard against electric shock

     Avoid body contact with earthed or 
     grounded surfaces (e.g. Pipes, radiators, 
     ranges refrigerators.)

4.  Keep children away

     Do not let visitors touch the tool or 
     extension code.

5.  Dress properly

     Do not wear loose clothing or jewelry, 
     they can be caugh in moving parts. Wear 
     protecting hair covering to contain long 
     hair.

6.  Do not abuse the cord

     Never carry the machine by cord or yank 
     it to disconnect it from the socket. Keep 
     the cord away from heat, oil, and sharp 
     edges..

7.  Maintain machine with care

     Follow instructions for lubrication and 
     changing accessories. Inspect tool cord 
     periodically. If damaged, have it repaired 
     by an authorized service facility.

P1

Summary of Contents for NC008














































Reviews: