Sirman TC RIO 12 Use And Maintenance Manual Download Page 1 | Manualshive

Page: 1 / 14

Sirman TC RIO 12 Use And Maintenance Manual Download Page 1

28

8 - Problems and solutions

8.1 - Problems, causes and solutions

Inconvenienti

1- The machine does not start
2- The propeller turns in the opposite direction of the one indicated by the
arrow (on the three-phase model)
3- The product is not ground correctly

Causes

1- The differential switch is in the position “0”
1- The plug switch is in the position "0"
1- Start push button does not work
1- The electric motor is defective

2- Contact technical assistance

3- Plate and blade have not been correctly tightened
3- grooves on the plate or blade is not perfectly sticking
(on the plate plane)
3- Outlet not perfectly introduced into the housing

Solutions

1- Put the switch at position “I”
1- Put the switch at position “I”
1- Contact technical assistance
1- Contact technical assistance

3- Correctly tighten the plate and blade
3- Replace the defective plate couple and the blade
3- Correctly introduce the outlet in the proper housing

1

MEAT MINCER

USE AND MAINTENANCE MANUAL

TC RIO 12
TC RIO 22
TC RIO 32

10/2003

1
2
3
...
»

Summary of Contents for TC RIO 12















Reviews:

No comments