SIP 08976 Assembly Instructions Manual Download Page 15

The manufacturer reserves the right to modify the declared data without advance notification 

1,5   m   

Suction height from a tank

 m/s

2      

Arm vibrations 

28 N /  26  N   

 Recoil force of gun at operating pressure (max) 

540 x 905  x  827 mm     (мм)     

Dimensions

• SIP warrants its products for 12 months from the date 

of purchase.

• In accordance with the above-mentioned terms, SIP 

agrees to furnish free of charge any replacement parts 

for such parts as, in the Manufacturer's opinion or that 

of their authorized representative, are defective either 

in material or manufacture. In any case transport and 

labour costs shall be charged to the customer. 

• The product returned to SIP or authorized representa-

tive for warranty inspection or repair must be sent back 

together with each single part the unit is complete with 

and must not have been improperly damaged. SIP will 

otherwise decline all responsibility for any warranty 

claims. 

• The warranty does not include any payment for faults 

due to incorrect usage by the operator and for parts 

falling within the usual maintenance, such as: Gaskets, 

diaphragms sealing rings, oil and so on. 

• The Manufacturer shall not be held responsible for 

accidents to the operator or third parties while the 

equipment is in use. 

• This warranty shall not be valid if:

a) previous service or repairs were performed by unau-

thorized 

individuals or companies.

b) the equipment was previously repaired with non-

original parts. 

• Breakdowns and failures in our machines during or 

after the warranty period, do not grant any right to su-

spend payments for the goods delivered which have 

already been agreed to. Nor can such breakdowns 

and failures be used to excuse further delay in such 

payments. 

• The Manufacturer reserves the right at any time to car-

ry out any and all changes to improve his products. Nor 

shall he be obliged by this to add such improvements to 

units previously manufactured, already consigned or in 

the process of installation. 

• These general conditions of warranty hereby substi-

tute and nullify every previous condition expressed or 

implicit.

WARRANTY CONDITIONS 

15

Summary of Contents for 08976

















Reviews: