Singxer SU-6 Handbook Download Page 2

SU-6 USB Audio Bridge Quick Start Handbook 

 
1. After getting the machine, please check whether the appearance of the machine is complete 
and the accessories are complete. 
2. The standard Ming Wei power adapter supports global voltage, the input voltage range is 85 ~ 
264VAC; the power plug is DC2.1, inside positive  and outside negative; insert the SU-6 power 
plug, the SU-6 rear panel plug above the power light is on as a result, the internal super capacitor 
starts to charge, charging takes about one minute, and the power light on the front panel lights 
up; 
3. Plug in the USB cable and connect to a computer or digital player. USB requires a 5V power 
supply. 
4. WINDOWS system needs to install the driver we provide, the latest version of WIN10 can be 
used free of driver, but it is recommended to use the driver we provide; Linux and MAC comes 
with a driver, no need to install a separate driver; 
5. After the computer or digital player recognizes the SU-6, set the player and select SU-6 as the 
output device; 
Click to play, the SU-6's PLAY light is on; 
 
6. The DSD light will only illuminate when the DSD is played. Most players are set correctly to play 
the DSD. 
If the DSD light is off, most of the cases are DSD playback settings; please refer to our other 
documentation for the setup procedure; 
7. The front panel of the SU-6 is an LED status display with no touch function; 
8. It takes about 1 minute to power on and about 1 minute to shut down. This is because the 
SU-6 has a built-in super capacitor. It takes time to charge and discharge. The SU-6 does not have 
a power switch. The SU-6 has low power consumption and can be used for a long time. The SU-6 
power plug supports hot swap. 
9. If the SU-6 needs to connect to other power sources, it needs a DC power supply voltage of 
7.5V-9V, a current of at least 2A, preferably 7.5V 3A. 
10. The SU-6 can be used normally for 1 minute. The super capacitor is fully charged for 20 
minutes. The internal thermostat is basically stable for 20 minutes and completely stable for 1 
hour. 
 
11. The two HDMI sockets of the SU-6 are I2S interfaces. They are not universal HDMI. They 
cannot be connected to monitors, TVs and computers. HDMI-I2S must be configured after the 
line sequence and then connected to other devices. 
 
 

Summary of Contents for SU-6

Page 1: ...Singxer SU 6 Handbook ...

Page 2: ... SU 6 s PLAY light is on 6 The DSD light will only illuminate when the DSD is played Most players are set correctly to play the DSD If the DSD light is off most of the cases are DSD playback settings please refer to our other documentation for the setup procedure 7 The front panel of the SU 6 is an LED status display with no touch function 8 It takes about 1 minute to power on and about 1 minute t...

Page 3: ...放器识别到 SU 6 之后 设置播放器 选择 SU 6 作为输出设 备 点击播放 SU 6 的 PLAY 灯亮起 6 DSD 灯只有在播放 DSD 的时候才会亮起 多数播放器设置正确才能播放 DSD 如果 DSD 灯不亮 大部分情况是 DSD 播放设置问题 设置步骤请参考我们的 其他文档 7 SU 6 的前面板是 LED 状态显示 没有触摸功能 8 SU 6 的电源开机需要 1 分钟左右 关机也需要 1 分钟左右 这是因为 SU 6 内置了超级电容 充电放电需要时间 SU 6 没有设置电源开关 是因为 SU 6 功耗不大 可以长期开机使用 SU 6 的电源插头支持带电插拔 9 SU 6 如果需要外接其他电源 需要直流电源电压为 7 5V 9V 电流至少 2A 最好是 7 5V 3A 的规则的电源 10 SU 6 开机 1 分钟可以正常使用播放 超级电容完全充满电需要 20 分钟 内 部恒温...

Page 4: ...S W4S SW1 DSD_ON OUTPUT FOR PIN13 HP13 OFF OFF OFF OFF OFF SW2 DSD_ON OUTPUT FOR PIN14 HP14 OFF OFF OFF ON OFF SW3 DSD_ON OUTPUT FOR PIN15 HP15 OFF OFF ON OFF OFF SW4 DSD_ON OUTPUT FOR PIN16 HP16 OFF OFF OFF OFF OFF SW5 CLK output mode OFF is MCLK ON is WCK WCLK LRCLK MC WCK OFF OFF OFF OFF OFF SW6 MCLK OUT CLOCK 22 5792 24 576MHz 45 1584 49 152Mhz OFF is 22 24M ON is 45 49M X2 OFF OFF OFF OFF OFF...

Reviews: